# Ducted heat pumps for Waltham's mixed housing

> Ducted heat pumps for Waltham ranches, colonials, two-families and condos, sized for inland cold, with Eversource rebates and gas backup still allowed.

URL: https://clementbostonheatpumps.com/service-areas/waltham/

Service area, Massachusetts

Ducted heat pumps for Waltham ranches, colonials, two-families and condos, sized for inland cold, with Eversource rebates and gas backup still allowed.

(857) 837-1475

Last Updated: November 12, 2026

Electric

Eversource

Rebates

Mass Save

Permits

Waltham Building Department

Energy code

Stretch code since July 1, 2012 (not the specialized code)

## A typical Warrendale oil-to-heat-pump switch

New air handler in the old furnace's place on the existing basement trunk

Outdoor unit on a raised stand beside the driveway, clear of the plow line

### An old furnace and good ducts

A 1950s Warrendale ranch runs a 24-year-old oil furnace and central air through perimeter ducts from a basement trunk. The furnace is near the end, oil bills are high, and the house has no gas service, so the choice is between another oil burner and a heat pump.

### Testing before reusing

Static pressure and leakage tests show sound ducts but a return sized for the old furnace. One added return from the bedroom wing brings static into range for a 3-ton cold-climate heat pump, and the accessible trunk joints are resealed with mastic before the new air handler takes the furnace's spot.

### Sized for Waltham's nights

Waltham sits inland, where nights at or below 10°F come far more often than at Logan. The load is calculated at the local design temperature, and the backup strips are locked out above the balance point. The outdoor unit goes on a raised stand beside the driveway, clear of the plow line.

### Oil out

Once the heat pump carries the house, the furnace leaves through the bulkhead and the 275-gallon tank is pumped, cleaned and removed under the fire department permit, with the fill and vent pipes capped outside. The old system's removal puts the job on Mass Save's whole-home path through Eversource.

*Project facts*

| Service | Oil furnace to heat pump on existing ducts |
| --- | --- |
| Where | Warrendale, Waltham |
| House | 1950s ranch, about 1,300 sq ft |
| Before | Oil furnace, central AC, 275-gallon tank |
| After | 3-ton cold-climate heat pump, added return |
| Price | $20,900 before rebates, tank removal included |
| Time on site | Four working days |

## What brings people to us in Waltham

### An oil furnace with ducts that still work

Ducts that reach every room can usually carry a heat pump once static pressure, return size and leakage are measured, and the tank comes out after.

### A condo on electric heat

Almost a quarter of Waltham homes heat with electricity. A ducted heat pump replaces the resistance heat and adds central cooling.

### A renovation that wants gas backup

Waltham hasn't adopted the specialized code or a fossil-fuel-free rule, so a heat pump with a gas furnace for the coldest hours is still allowed.

Waltham never adopted the specialized energy code, and that leaves its owners more choices than most cities near Boston. [Clement Boston Heat Pumps](https://clementbostonheatpumps.com/) brings that wider menu to heat pump installation in Waltham, MA: full electric, gas backup, or a staged switch.

Which option fits depends on what heats the house today. Waltham’s mix is unusual: nearly one home in five still burns oil, and almost a quarter heat with electricity.

## What’s different about heating a Waltham house

Three facts set the plan here: a lighter energy code than the neighbors, a big share of oil and electric heat, and colder nights than downtown Boston.

### The stretch code, not the specialized code

Newton, Watertown and Lexington have moved to the specialized code, which steers new homes and major renovations toward all-electric or pre-wired designs. Waltham stays on the stretch code it adopted on July 1, 2012.

In practice, a Waltham renovation can still pair a heat pump with a new gas furnace. Whether that’s the better plan depends on the house; the [dual fuel page](https://clementbostonheatpumps.com/dual-fuel-heat-pump/) explains when it earns its keep.

### Oil and electric heat

Waltham’s fuel mix is roughly 53% gas, 24% electric and 19% oil, against a state average of about 22% oil. Oil and electric homes have the strongest running-cost case, and both are eligible for Mass Save’s whole-home rebate once the old system is out.

### Inland cold

Waltham sits about 12 miles west of downtown, away from the harbor. Hanscom Field in Bedford, the closest long-record inland station, averages about 19 nights a year at or below 10°F, against fewer than seven at Logan.

That changes the sizing. We calculate the load at Waltham’s design temperature and pick equipment by its output at 5°F; see the [sizing guide](https://clementbostonheatpumps.com/guide/heat-pump-sizing/).

## From oil tank to heat pump

About 19% of Waltham homes burn oil. Where the burner is a forced-air furnace, the ducts are already in place and the conversion is mostly equipment.

### Reusing the ducts

A forced-air oil furnace means the ducts already exist. We measure static pressure, check that the return is big enough for a heat pump’s airflow and look for leaky joints before deciding to reuse them. When they pass, the job is mostly equipment; see [oil to heat pump](https://clementbostonheatpumps.com/oil-to-heat-pump-conversion/).

### The tank comes out

Once the heat pump carries the house, the oil tank goes. Our typical range for an accessible basement tank is $600 to $1,500; buried tanks are priced on site. The [oil tank removal page](https://clementbostonheatpumps.com/oil-tank-removal/) covers the process.

### Running cost

Per unit of heat delivered, oil costs more than a heat pump on Eversource’s winter rate, which lowers distribution and transmission charges from November through April. The [heat pump vs oil guide](https://clementbostonheatpumps.com/guide/heat-pump-vs-oil-heat/) works through the comparison.

## Waltham’s housing, block by block

Waltham is a mix: just over a third detached houses, about a tenth two-families, and nearly a third in larger buildings. Only 28% predates 1940, below Boston’s inner suburbs.

| Waltham home type | Share | What the ducted plan looks like |
| --- | --- | --- |
| Detached house | 37.0% | Reuse existing ducts, or basement plus attic air handlers |
| Two-family | 10.9% | One system per unit |
| Three or four units | 12.0% | Per unit, closet air handlers in the middle |
| Five or more units | 31.1% | Unit by unit, with the association |

### South Side and older two-families

On the South Side near Moody Street, many of the older two-families and small multi-families were built for radiators. Those floors get their own systems, with the attic and basement carrying the top and bottom units.

### Warrendale, the Highlands and post-war streets

Further from the river, ranches, capes and colonials from the mid-century on often have a furnace and central air. That’s the simplest heat pump job in Waltham; see [furnace to heat pump](https://clementbostonheatpumps.com/furnace-to-heat-pump-conversion/). A split-level or a ranch with ducts in a crawlspace or slab needs a closer look at duct condition before we commit to reusing them.

### Condos and apartments

Where a condo or apartment heats with baseboard or wall heaters, a ducted heat pump replaces them room by room and adds cooling. See [baseboard to heat pump](https://clementbostonheatpumps.com/baseboard-heat-to-heat-pump/).

## Backup heat and comfort on cold nights

On the coldest nights a heat pump’s output drops while the house needs more. How that gap gets covered is a design choice, not an afterthought.

### Electric strips or a gas furnace

A whole-home system uses electric strips in the air handler for the few hours a correctly sized heat pump can’t cover. A dual fuel system uses a gas furnace instead, which Waltham’s code still allows. The [backup heat guide](https://clementbostonheatpumps.com/guide/heat-pump-aux-heat/) explains how the lockout temperature is set.

### Will it keep up?

Cold-climate units hold most of their capacity well below freezing. Our guide to [whether heat pumps work in Massachusetts](https://clementbostonheatpumps.com/guide/do-heat-pumps-work-in-massachusetts/) explains the physics and the equipment listing that Mass Save requires.

## What the town and Eversource need from a Waltham job

Waltham’s Building Department issues the electrical and sheet metal permits, plus a gas permit where a line is capped. The filing route and fees are confirmed per address.

| What | The Waltham picture |
| --- | --- |
| Electric utility | Eversource |
| Gas utility | National Grid |
| Energy code | Stretch code since July 1, 2012 |
| Heating fuel mix | Gas 53.4%, electricity 23.5%, oil 18.9% |
| Built before 1940 | 28.3% |

Mass Save’s whole-home rebate needs cold-climate listed equipment, an installer in its network, the old system out and proof of weatherization; the [rebate guide](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/) has the details.

## Start to finish in Waltham

On the first visit we work out the heat loss room by room at Waltham’s design temperature, test the existing ducts, check the panel and pick an outdoor spot clear of the driveway and the plow.

- **Estimate:** each line priced, from equipment and its 5°F capacity to ducts, wiring, permits, the tank and the rebate tier.
- **Permits,** then three to six working days on site for a house with usable ducts, longer where new ducts go in.
- **Old system out** once the heat pump carries the house, then the tank.
- **Commissioning:** nitrogen test, deep vacuum, refrigerant weighed in, airflow and static recorded, backup lockout set.

[Newton](https://clementbostonheatpumps.com/service-areas/newton/) and [Watertown](https://clementbostonheatpumps.com/service-areas/watertown/) border Waltham to the south and east; [Belmont](https://clementbostonheatpumps.com/service-areas/belmont/) runs its own light plant.

## Services in Waltham

- [Service**Oil to heat pump conversion** Retire the oil furnace or hydro-air boiler, cap the oil line and heat and cool through the ducts you have.](https://clementbostonheatpumps.com/oil-to-heat-pump-conversion/)
- [Service**Furnace to heat pump conversion** Take out the gas or propane furnace and heat and cool through the same ducts with a heat pump.](https://clementbostonheatpumps.com/furnace-to-heat-pump-conversion/)
- [Service**Whole-home heat pumps** One ducted system that heats and cools the whole house, with the furnace or boiler retired.](https://clementbostonheatpumps.com/whole-home-heat-pump/)
- [Service**Oil tank removal** The old basement tank pumped, cleaned, removed and permitted once the heat pump is running.](https://clementbostonheatpumps.com/oil-tank-removal/)
- [Service**Dual fuel heat pumps** A heat pump paired with the furnace you keep, with one control deciding which one heats.](https://clementbostonheatpumps.com/dual-fuel-heat-pump/)
- [Service**Baseboard heat to heat pump** Replace electric baseboard with a ducted heat pump that heats on far less electricity and cools too.](https://clementbostonheatpumps.com/baseboard-heat-to-heat-pump/)

## How a job usually runs in Waltham

### First call

You tell us what heats and cools the house now, which rooms aren't working, and roughly where the house is.

### Home visit

We measure the house for a load calculation, test the ducts, check the panel and look for an outdoor spot.

### Written estimate

Equipment, duct changes, electrical, permits and the rebate path, line by line, with our price.

### Install

Permits first, then the work: usually two to five working days on site.

### Commissioning

Pressure test, vacuum, charge by weight, airflow and controls set before we call it done.

## Neighborhoods, landmarks and routes

- South Side
- Warrendale
- The Highlands
- Piety Corner
- Cedarwood
- Lakeview
- Bleachery
- Northeast Waltham

### Landmarks

- Charles River Museum of Industry
- Moody Street
- Prospect Hill Park
- Gore Place
- Brandeis University

### Getting around

- Route 128
- Route 20
- Route 117
- Route 60
- Moody Street

[Open Waltham, MA in Google Maps](https://www.google.com/maps/search/?api=1&query=Waltham%2C%20MA)

## Waltham: questions

### Does Waltham's energy code stop me from keeping gas heat?

No. Waltham has followed the stretch energy code since July 1, 2012 and hasn't adopted the specialized code or a fossil-fuel-free rule. A renovation can be designed with gas backup, subject to the stretch code's paths, and an ordinary replacement is unaffected.

### What does it cost to convert a Waltham oil house to a heat pump?

If the ducts can be reused, our typical range is $15,000 to $28,000 and up before rebates, plus $600 to $1,500 for an accessible basement tank. Where new ducts are needed, our typical range is $20,000 to $40,000 and up. The written estimate sets the price.

### Is a heat pump big enough for a cold Waltham night?

A correctly sized cold-climate unit is. Hanscom Field, the nearest inland weather station north of Waltham, averages about five nights a year at or below 0°F. We size to the local design temperature and check the unit's rated capacity at 5°F.

### Who sponsors Mass Save rebates for Waltham homes?

Eversource for homes heated by oil, propane or electricity, since Eversource supplies Waltham's power. National Grid, Waltham's gas company, sponsors them for gas-heated homes. The amounts and equipment rules are the same.

### Do I file the Waltham building permit for my heat pump myself?

No. The electrical and sheet metal permits go through Waltham's Building Department under the licensed trades doing the work. The filing route and fees are confirmed per address, and we schedule the install once permits are issued.

## Nearby service areas

- [Service area**Newton** Ducted heat pumps for Newton colonials, Victorians and two-families, planned around the city's fossil-fuel-free ordinance and the specialized energy code.](https://clementbostonheatpumps.com/service-areas/newton/)
- [Service area**Watertown** Ducted heat pumps for Watertown two-families and single homes, one system per unit, on Eversource with Mass Save rebates and dual fuel still allowed.](https://clementbostonheatpumps.com/service-areas/watertown/)
- [Service area**Belmont** Ducted heat pumps for Belmont homes, with the rebate path set by your fuel. Belmont Light pays for oil and propane switches; gas homes can use Mass Save.](https://clementbostonheatpumps.com/service-areas/belmont/)

## Guides for houses in Waltham

- [Decision Guide**Is a heat pump better than oil heat in Massachusetts?** Running cost worked out from Massachusetts fuel prices and winter heat pump rates, plus the comfort, cooling, tank and hot water questions that come with the switch.](https://clementbostonheatpumps.com/guide/heat-pump-vs-oil-heat/)
- [Learn**Do heat pumps work in Massachusetts?** What a Boston-area winter asks of a heat pump, how cold-climate equipment is rated, and what changes inland, in snow and on the coldest nights.](https://clementbostonheatpumps.com/guide/do-heat-pumps-work-in-massachusetts/)
- [Learn**What size heat pump do I need?** Why square footage and the old unit's tonnage both mislead, what a room-by-room load calculation measures, and how the result turns into equipment.](https://clementbostonheatpumps.com/guide/heat-pump-sizing/)
- [Learn**Why does my heat pump's aux heat keep coming on?** Backup heat is part of every cold-climate system. Here's when it should run, when it shouldn't, and the settings that decide which.](https://clementbostonheatpumps.com/guide/heat-pump-aux-heat/)
- [Learn**How do Mass Save heat pump rebates work?** The three rebate tiers, the conditions behind each, the dates that change them, and what happens in towns with their own light plant.](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/)

## Get an estimate in Waltham

Tell us what heats the house now and which rooms aren't working in Waltham.

(857) 837-1475
