# Ducted heat pumps for Revere homes near the water and inland

> Ducted heat pumps for Revere homes from Beachmont to Point of Pines, mounted for salt air and flood zones, with National Grid rebates and CitizenServe permits.

URL: https://clementbostonheatpumps.com/service-areas/revere/

Service area, Massachusetts

Ducted heat pumps for Revere homes from Beachmont to Point of Pines, mounted for salt air and flood zones, with National Grid rebates and CitizenServe permits.

(857) 837-1475

Last Updated: November 12, 2026

Electric

National Grid

Rebates

Mass Save

Permits

Revere Inspectional Services

Energy code

Stretch code since January 1, 2012 (not the specialized code)

## What a furnace-to-heat-pump job in Beachmont looks like

Coastal-protected outdoor unit on a wall bracket above the flood line on the sheltered side

New air handler in the partial basement on the existing duct trunk

### Salt got there first

A 1920s Beachmont house a few blocks from the water has a 20-year-old gas furnace and a central air condenser whose coil has corroded through in the salt air. The AC has quit, and the owner prefers to replace both systems at once rather than buy another condenser for an old furnace.

### Up and out of the spray

The parcel sits in a mapped flood zone, so a ground pad is out. A coastal-protected outdoor unit goes on a stainless wall bracket above the design flood level, on the side of the house away from the onshore wind, in the open where rain can rinse the coil.

### Reusing the ducts

Static pressure and leakage tests show the existing ducts can carry a 3-ton cold-climate heat pump, so a new air handler takes the furnace's place in the low partial basement. A licensed gas fitter caps the line, and the old furnace and condenser leave the same day.

### Planned to last

Permits go through Revere's CitizenServe portal. With the furnace removed, the job follows Mass Save's whole-home path through National Grid. The maintenance note left with the owner covers a yearly fresh-water rinse of the coil and a spring check of the bracket fasteners for rust.

*Project facts*

| Service | Gas furnace and AC to heat pump |
| --- | --- |
| Where | Beachmont, Revere |
| House | 1920s two-story single-family, about 1,600 sq ft |
| Before | Gas furnace, salt-corroded central AC |
| After | 3-ton heat pump on existing ducts, raised coastal mount |
| Price | $19,800 before rebates |
| Time on site | Four working days |

## What brings people to us in Revere

### A house a block from the beach

Onshore wind carries salt to the coil. The unit goes on the sheltered side, where rain still rinses it, and a coastal-protected model where the maker offers one.

### A lot in a mapped flood zone

The building code's flood provisions lift equipment above the design flood level, on a wall bracket or a raised platform.

### A two-family with one owner ready to switch

Each floor gets its own ducted system, so one unit can convert now and the other later.

### A condo or apartment on electric heat

A quarter of Revere homes heat with electricity; a ducted heat pump replaces it and cools in summer.

Salt spray off Revere Beach is hard on an outdoor coil, so a Revere heat pump plan starts with where the unit sits and how high. [Clement Boston Heat Pumps](https://clementbostonheatpumps.com/) builds that into every heat pump installation in Revere, MA, before we choose equipment.

Revere is one of the state’s coastal communities, with low ground in Beachmont, Point of Pines and along Revere Beach Boulevard. Mounting comes first; sizing and ducts follow.

## Mounting for salt and water

Massachusetts has no siting rule for heat pumps near salt water, so we follow the makers’ coastal guidance and the building code’s flood provisions. Both shape the mount before anything else.

### Keeping salt off the coil

Onshore wind drives salt into an outdoor coil’s fins and fasteners. We put the unit on the side of the house away from the prevailing sea breeze, but in the open, where rain can wash it rather than under an eave that keeps salt on it.

Where the maker offers a coastal-protected version with treated coils and cabinet, we specify it for houses within sight of the water. Our [maintenance page](https://clementbostonheatpumps.com/heat-pump-maintenance/) covers the yearly fresh-water rinse.

### Flood zones

Low-lying Revere parcels may sit in a mapped flood zone, which is checked per address. Where a zone applies, the building code’s flood provisions call for equipment above the design flood level. A wall bracket or a raised, anchored platform does that, with the line set and power whip routed to match.

### Snow and wind

Revere’s coastal location keeps winters milder than inland towns, but wind piles snow against walls. The mount clears the drift line as well as the flood line; see the [snow stand guide](https://clementbostonheatpumps.com/guide/heat-pump-snow-stand/).

## Revere’s houses and how the ducts fit

Revere’s homes are newer on average than Boston’s inner suburbs: about a quarter predate 1940. A quarter are detached houses and nearly as many are two-families.

| Revere home type | Share | The ducted plan |
| --- | --- | --- |
| Detached house | 25.4% | Reuse ducts, or basement plus attic air handlers |
| Two-family | 23.6% | One system per unit |
| Three or four units | 11.5% | Per unit, attic and basement first |
| Five or more units | 30.8% | Unit by unit, with the association |

### Houses with a furnace and central air

A Revere single-family with a gas furnace and aging central air is a straightforward conversion when the ducts test well. The heat pump replaces both, using the same ducts; see [replacing AC with a heat pump](https://clementbostonheatpumps.com/replace-ac-with-heat-pump/) and [furnace to heat pump](https://clementbostonheatpumps.com/furnace-to-heat-pump-conversion/).

### Two-families

In West Revere and around Revere Center, two-families get one system per floor, each with its own thermostat and electric bill. The first floor works from the basement, the second from the attic.

Each outdoor unit gets its own spot and its own mount, which on a narrow Revere lot often means one at the rear and one on a bracket along the side wall.

### Condos along the beach

Where a condo near the beach heats with electricity, a ducted heat pump replaces it unit by unit. The association decides where outdoor units can sit; our [condo guide](https://clementbostonheatpumps.com/guide/condo-heat-pump-replacement/) lists what boards ask for.

## Electric heat, gas and oil in Revere

Gas heats about 58% of Revere homes, electricity about 25% and oil about 13%. The fuel you’re leaving sets the rebate path and the savings.

### Leaving electric resistance

Baseboard turns each kilowatt-hour into one unit of heat; a heat pump delivers two to three on a typical winter day. Mass Save counts electric resistance as an eligible system to replace. See [baseboard to heat pump](https://clementbostonheatpumps.com/baseboard-heat-to-heat-pump/).

### Leaving oil

Oil is the most expensive common fuel per unit of heat, and a heat pump on National Grid’s winter rate runs below it. The tank comes out after the conversion; see [oil to heat pump](https://clementbostonheatpumps.com/oil-to-heat-pump-conversion/).

### Leaving gas, or keeping it as backup

Revere follows the stretch code and is not a fossil-fuel-free town, so a renovation can keep a gas furnace beside the heat pump. A whole-home system with the furnace removed earns the larger rebate.

## When the power goes out

Coastal storms bring outages, and a heat pump needs electricity to run. So do a gas furnace’s blower and controls, so neither keeps heating through a blackout on its own.

### Planning for outages

Our [power outage guide](https://clementbostonheatpumps.com/guide/heat-pump-power-outage/) explains what a generator or backup plan needs to carry a heat pump: the starting and running load of the outdoor unit, the air handler’s blower, and whether the backup strips stay off while on generator power.

### Planning for the long run

Salt exposure is one of the factors that shortens equipment life near the water. The [lifespan guide](https://clementbostonheatpumps.com/guide/heat-pump-lifespan/) covers what wears out first and how maintenance stretches it, from coil rinsing to checking the mount’s fasteners for rust each spring.

## Permits and the National Grid side in Revere

Revere Inspectional Services takes building permits through the CitizenServe portal linked from the city’s site. A ducted job needs electrical and sheet metal permits, plus gas where a line is capped.

| What | The Revere picture |
| --- | --- |
| Permit portal | CitizenServe |
| Electric and gas utility | National Grid |
| Energy code | Stretch code since January 1, 2012 |
| Coastal community | Yes, North Shore region |
| Heating fuel mix | Gas 57.6%, electricity 25.1%, oil 12.5% |

National Grid sponsors Mass Save rebates in Revere for electric and gas homes alike, and its seasonal heat pump rate trims winter distribution charges; see the [electric rate guide](https://clementbostonheatpumps.com/guide/heat-pump-electric-rate-massachusetts/).

## Steps on a Revere install

The visit starts outside: wind direction, distance to the water, the flood map for your parcel and the drift line. Inside, we measure the heat loss room by room, test the ducts and check the panel.

- **Written estimate:** equipment and its 5°F capacity, the coastal mount, ducts, wiring, permits, rebate tier and price.
- **Permits** through CitizenServe, then three to seven working days on site.
- **Mount first,** so the line set and power reach the unit at its final height.
- **Commissioning:** pressure-tested lines, a deep vacuum, refrigerant charged by weight, airflow and static measured, controls programmed.

[Winthrop](https://clementbostonheatpumps.com/service-areas/winthrop/) shares Revere’s harbor exposure; [Chelsea](https://clementbostonheatpumps.com/service-areas/chelsea/) and [Lynn](https://clementbostonheatpumps.com/service-areas/lynn/) are next door to the southwest and up the shore.

## Services in Revere

- [Service**Furnace to heat pump conversion** Take out the gas or propane furnace and heat and cool through the same ducts with a heat pump.](https://clementbostonheatpumps.com/furnace-to-heat-pump-conversion/)
- [Service**Whole-home heat pumps** One ducted system that heats and cools the whole house, with the furnace or boiler retired.](https://clementbostonheatpumps.com/whole-home-heat-pump/)
- [Service**Replace AC with a heat pump** When the central AC dies, a heat pump on the same ducts cools and adds a second source of heat.](https://clementbostonheatpumps.com/replace-ac-with-heat-pump/)
- [Service**Baseboard heat to heat pump** Replace electric baseboard with a ducted heat pump that heats on far less electricity and cools too.](https://clementbostonheatpumps.com/baseboard-heat-to-heat-pump/)
- [Service**Oil to heat pump conversion** Retire the oil furnace or hydro-air boiler, cap the oil line and heat and cool through the ducts you have.](https://clementbostonheatpumps.com/oil-to-heat-pump-conversion/)
- [Service**Heat pump maintenance** A yearly check of filters, coils, drains, defrost, charge and airflow on ducted heat pumps.](https://clementbostonheatpumps.com/heat-pump-maintenance/)

## How a job usually runs in Revere

### First call

You tell us what heats and cools the house now, which rooms aren't working, and roughly where the house is.

### Home visit

We measure the house for a load calculation, test the ducts, check the panel and look for an outdoor spot.

### Written estimate

Equipment, duct changes, electrical, permits and the rebate path, line by line, with our price.

### Install

Permits first, then the work: usually two to five working days on site.

### Commissioning

Pressure test, vacuum, charge by weight, airflow and controls set before we call it done.

## Neighborhoods, landmarks and routes

- Beachmont
- Point of Pines
- Oak Island
- Shirley Avenue
- Revere Center
- West Revere
- North Revere
- Wonderland

### Landmarks

- Revere Beach Reservation
- Rumney Marsh Reservation
- Wonderland station
- Northgate Shopping Center

### Getting around

- Route 1A
- Route 1
- Route 60
- Revere Beach Parkway
- Revere Beach Boulevard

[Open Revere, MA in Google Maps](https://www.google.com/maps/search/?api=1&query=Revere%2C%20MA)

## Revere: questions

### Does salt air shorten a heat pump's life in Revere?

Salt spray and onshore wind speed up corrosion on outdoor coils and fasteners, which is why makers offer coastal-protected models. Placement out of direct spray, a level mount that drains, and a fresh-water rinse during maintenance all help the unit last.

### How do I know if my Revere house is in a flood zone?

Flood zones are mapped parcel by parcel, so we check your address before choosing the mount. Where a zone applies, the state building code's flood provisions require equipment above the design flood level, which usually means a wall bracket or a raised platform.

### What does a ducted heat pump cost near Revere Beach?

On ducts we can reuse, our typical range is $15,000 to $28,000 and up before rebates; with new ductwork it is $20,000 to $40,000 and up. A raised coastal mount is a line in the estimate, which the home visit sets.

### How do I get a heat pump permit in Revere?

Revere takes building permits through its online CitizenServe portal, linked from the city's website. A ducted heat pump needs an electrical permit and a sheet metal permit, filed by the licensed trades doing the work.

### Can a Revere renovation keep gas heat as backup?

Yes. Revere follows the stretch code, in place since January 1, 2012, and hasn't adopted the specialized code or a fossil-fuel-free rule. A heat pump with a gas furnace for the coldest hours is still allowed.

## Nearby service areas

- [Service area**Winthrop** Ducted heat pumps for Winthrop homes, placed out of the salt wind and above flood levels, on National Grid with Mass Save rebates and the stretch code.](https://clementbostonheatpumps.com/service-areas/winthrop/)
- [Service area**Chelsea** Ducted heat pumps for Chelsea three-deckers and condos, one system per floor, with outdoor units fitted to tight lots and roofs on Eversource's winter rate.](https://clementbostonheatpumps.com/service-areas/chelsea/)
- [Service area**Lynn** Ducted heat pumps for Lynn three-deckers, two-families and shore houses, with permits through Lynn's online ISD portal and National Grid rebates.](https://clementbostonheatpumps.com/service-areas/lynn/)

## Guides for houses in Revere

- [Learn**How high should a heat pump snow stand be, and where should the outdoor unit go?** The outdoor unit pulls heat from winter air, so snow, ice, salt and the neighbors all shape where it goes and what it sits on.](https://clementbostonheatpumps.com/guide/heat-pump-snow-stand/)
- [Learn**How long does a heat pump last?** No one can promise a heat pump a number of years. What you can control is the install, the sizing and the upkeep that decide most of it.](https://clementbostonheatpumps.com/guide/heat-pump-lifespan/)
- [Decision Guide**What happens to a heat pump during a power outage?** A heat pump stops when the power goes out. So does almost every other central heating system. Here's what backup actually works, and what it takes.](https://clementbostonheatpumps.com/guide/heat-pump-power-outage/)
- [Learn**How does the heat pump electric rate work in Massachusetts?** Which part of your electric bill the seasonal rate lowers, why it applies to the whole house, how enrollment works, and what it means for the switch from oil or gas.](https://clementbostonheatpumps.com/guide/heat-pump-electric-rate-massachusetts/)
- [Decision Guide**What's involved in replacing a heat pump in a condo?** In a condo, the outdoor unit usually sits on common property, so the association, the master deed and sometimes a historic commission come before equipment.](https://clementbostonheatpumps.com/guide/condo-heat-pump-replacement/)

## Get an estimate in Revere

Tell us what heats the house now and which rooms aren't working in Revere.

(857) 837-1475
