# Ducted heat pumps for Newton houses and renovations

> Ducted heat pumps for Newton colonials, Victorians and two-families, planned around the city's fossil-fuel-free ordinance and the specialized energy code.

URL: https://clementbostonheatpumps.com/service-areas/newton/

Service area, Massachusetts

Ducted heat pumps for Newton colonials, Victorians and two-families, planned around the city's fossil-fuel-free ordinance and the specialized energy code.

(857) 837-1475

Last Updated: November 12, 2026

Electric

Eversource

Rebates

Mass Save

Permits

Newton Inspectional Services Department

Energy code

Specialized stretch code since January 1, 2024

## Inside an Auburndale furnace-to-heat-pump renovation

New ceiling registers in a renovated second-floor bedroom

Two outdoor units on stands behind the new rear addition

### A renovation under the ordinance

A 1920s Auburndale colonial is getting a new kitchen, a second-floor bath and a rear addition. Inspectional Services confirms it is a major renovation, so Newton's fossil-fuel-free ordinance rules out a new gas furnace. The old one is 22 years old, and the bedrooms upstairs have always run cold.

### Splitting the floors

A 2.5-ton basement air handler takes over the first floor, reusing the old ducts after a leakage test and sealing, with three new branches into the addition. A 2-ton attic unit feeds seven new ceiling registers upstairs, which finally fixes the weak second-floor airflow the furnace never solved.

### Working with the builder

Ducts are roughed in while the addition and bath ceilings are open, so no finished plaster gets cut. The panel is checked against the whole all-electric renovation, a licensed gas fitter caps the furnace line, and two outdoor units go on stands behind the addition, away from the neighbors' windows.

### Sized for inland nights

Newton's coldest nights run below Logan's, so both systems are sized at the local design temperature to carry the house without gas. The result is a renovation that meets the ordinance and the specialized code, with even heat and cooling on both floors and no gas meter left feeding the heating system.

*Project facts*

| Service | Gas furnace to two ducted heat pumps |
| --- | --- |
| Where | Auburndale, Newton |
| House | 1920s colonial, about 2,400 sq ft, under renovation |
| Before | Gas furnace, failing central AC, weak upstairs airflow |
| After | 2.5-ton basement and 2-ton attic heat pumps |
| Price | $34,600 before rebates |
| Time on site | Eight working days, timed around the renovation |

## What brings people to us in Newton

### A gut renovation that can't add gas

Newton's fossil-fuel-free ordinance keeps new gas equipment out of new buildings and major renovations, so the renovated house heats with electricity.

### A colonial with a furnace downstairs and nothing upstairs

The first floor keeps its ducts; an attic air handler reaches the bedrooms, which on many older houses were never ducted.

### A gas furnace near the end, no renovation planned

An ordinary replacement isn't covered by the ordinance, so you can choose a full heat pump or a heat pump with gas backup.

### Oil in the basement

About one Newton home in eight still burns oil, and that group has the clearest running-cost case for a heat pump.

A Newton colonial on a gas furnace has two very different paths, depending on whether you’re renovating. So the first question [Clement Boston Heat Pumps](https://clementbostonheatpumps.com/) asks on any heat pump installation in Newton, MA is whether the work counts as a major renovation.

Since January 1, 2025, Newton’s fossil-fuel-free ordinance has kept new gas equipment out of new buildings and major renovations. A plain furnace replacement isn’t covered, so you can still choose gas backup there.

## Renovating in Newton: what the ordinance changes

The ordinance is part of the state’s fossil-fuel-free demonstration program, which Newton joined alongside Brookline, Cambridge, Arlington and a few others. It changes the heating plan only when the project is big enough.

### Inside a major renovation

New fossil-fuel equipment can’t go into the scope of a major renovation, so a heat pump paired with a new gas furnace is off the table there. The heat pump becomes the main system, sized to carry the coldest night without leaning on electric strips.

Exactly where Newton draws the major-renovation line is set in its ordinance. We confirm it with Inspectional Services before the design is final.

### Outside a renovation

Replacing a failing furnace or adding cooling is not a major renovation. You can choose a full [whole-home heat pump](https://clementbostonheatpumps.com/whole-home-heat-pump/) or a [dual fuel system](https://clementbostonheatpumps.com/dual-fuel-heat-pump/) that keeps the furnace for the coldest hours. The rebate differs: whole-home pays more, but needs the old system out.

### The specialized code

Newton has also followed the specialized stretch code since January 1, 2024. It applies to new construction and major renovations, steering them toward all-electric or pre-wired designs. A like-for-like heat pump retrofit is unaffected.

## Newton houses and where the ducts go

More than half of Newton’s homes are detached houses, and nearly half were built before 1940. That mix decides most layouts.

| Newton home type | Share of homes | The usual ducted layout |
| --- | --- | --- |
| Detached house | 54.8% | Basement trunk for the first floor, attic air handler upstairs |
| Two-family | 15.5% | One system per unit |
| Three or four units | 5.0% | Per unit, attic and basement first |
| Five or more units | 17.0% | Unit by unit, with the association |

### Colonials and Victorians

Many older colonials in West Newton, Auburndale and Newtonville have a basement furnace that feeds the first floor well and the bedrooms poorly. An [attic air handler](https://clementbostonheatpumps.com/attic-air-handler-heat-pump/) for the second floor fixes that, with short insulated branches through the ceilings.

Victorians with radiators need new ducts throughout; our [old houses guide](https://clementbostonheatpumps.com/guide/heat-pumps-in-old-houses/) shows how stacked closets carry the trunk.

### Two-families near the village centers

In Nonantum and Newton Corner, two-families get one system per unit, each sized for its own floor. See [heat pump ductwork](https://clementbostonheatpumps.com/heat-pump-ductwork/) for duct sizing and sealing.

## Gas, oil and running cost in Newton

Gas heats about 71% of Newton homes, oil about 13% and electricity about 13%. Your fuel decides the rebate sponsor and how quickly a heat pump pays its way.

### If you heat with gas

Gas is the cheapest fuel per unit of heat, so the running cost is closer than with oil. The usual reasons to leave gas are an old furnace, failing central air, or a renovation that rules out new gas. The [heat pump vs gas furnace guide](https://clementbostonheatpumps.com/guide/heat-pump-vs-gas-furnace-massachusetts/) works through the numbers.

### If you heat with oil

Oil costs more per unit of heat than a heat pump on Eversource’s winter rate, which lowers both distribution and transmission charges from November through April. See [oil to heat pump](https://clementbostonheatpumps.com/oil-to-heat-pump-conversion/).

### Sizing for inland nights

Newton sits inland, where the coldest nights run lower than at Logan. We run the room-by-room load at the local design temperature; our [sizing guide](https://clementbostonheatpumps.com/guide/heat-pump-sizing/) explains why oversizing costs comfort as well as money.

## The panel, the yard and the street

Two smaller questions decide the last details of a Newton plan: whether the electrical service can carry an all-electric house, and where the outdoor unit sits on the lot.

### When a renovation goes all-electric

A house that loses its gas furnace, and sometimes its gas range and water heater in the same renovation, adds a lot of electric load. We do a load calculation on the panel at the first visit, counting every new appliance in the renovation plan, not only the heat pump.

Where the service has to grow, our typical range for an upgrade is $3,000 to $6,500, and Eversource sets the timing for the new connection. Scheduling it early keeps it off the renovation’s critical path; see [panel upgrades](https://clementbostonheatpumps.com/electrical-panel-upgrade-for-heat-pump/).

### Placement on a Newton lot

Newton lots are larger than those closer to Boston, which usually leaves room for a rear-yard unit well back from the property line. We keep units off the driveway side where plowed snow piles up, and raise them on a stand above the drift line.

If the house sits in a local historic district, exterior review for a unit visible from the street is confirmed per address. Our [snow stand guide](https://clementbostonheatpumps.com/guide/heat-pump-snow-stand/) covers heights and clearances.

## What the town and Eversource need from a Newton job

Newton’s Inspectional Services Department issues the electrical and sheet metal permits, plus a building permit when the work is part of a renovation. Fees and the filing route are confirmed per address.

| What | The Newton picture |
| --- | --- |
| Electric utility | Eversource |
| Gas utility | National Grid |
| Energy code | Specialized stretch code since January 1, 2024 |
| Fossil-fuel-free ordinance | In effect since January 1, 2025 |
| Heating fuel mix | Gas 70.7%, oil 12.7%, electricity 13.4% |
| Homes built before 1940 | 48.8% |

Eversource sponsors Mass Save rebates for oil, propane and electric homes; National Grid sponsors them for gas homes. The [rebate guide](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/) lists the conditions and the [cost guide](https://clementbostonheatpumps.com/guide/heat-pump-installation-cost-massachusetts/) our ranges.

## What to expect on a Newton job

The first visit settles whether the project is a major renovation, then covers the room-by-room load, the ducts, the panel and an outdoor spot away from the neighbor’s windows.

- **Written estimate:** equipment with capacity at 5°F, duct work, electrical, permits, the rebate path and price.
- **Renovation timing:** ducts roughed in while ceilings and walls are open, on the builder’s schedule.
- **Install,** usually three to nine working days depending on new ducts.
- **Commissioning:** pressure test, vacuum below 500 microns, charge by weight, airflow and static measured, controls set.

[Watertown](https://clementbostonheatpumps.com/service-areas/watertown/) to the north allows gas backup in renovations; [Needham](https://clementbostonheatpumps.com/service-areas/needham/) and [Wellesley](https://clementbostonheatpumps.com/service-areas/wellesley/) lie to the south and west.

## Services in Newton

- [Service**Furnace to heat pump conversion** Take out the gas or propane furnace and heat and cool through the same ducts with a heat pump.](https://clementbostonheatpumps.com/furnace-to-heat-pump-conversion/)
- [Service**Whole-home heat pumps** One ducted system that heats and cools the whole house, with the furnace or boiler retired.](https://clementbostonheatpumps.com/whole-home-heat-pump/)
- [Service**Attic air handlers** An attic air handler that heats and cools the upper floor, with short sealed ducts and a guarded drain.](https://clementbostonheatpumps.com/attic-air-handler-heat-pump/)
- [Service**Heat pump ductwork** Duct testing, sealing, new returns and resized runs so a heat pump gets the air it needs.](https://clementbostonheatpumps.com/heat-pump-ductwork/)
- [Service**Oil to heat pump conversion** Retire the oil furnace or hydro-air boiler, cap the oil line and heat and cool through the ducts you have.](https://clementbostonheatpumps.com/oil-to-heat-pump-conversion/)
- [Service**Dual fuel heat pumps** A heat pump paired with the furnace you keep, with one control deciding which one heats.](https://clementbostonheatpumps.com/dual-fuel-heat-pump/)

## How a job usually runs in Newton

### First call

You tell us what heats and cools the house now, which rooms aren't working, and roughly where the house is.

### Home visit

We measure the house for a load calculation, test the ducts, check the panel and look for an outdoor spot.

### Written estimate

Equipment, duct changes, electrical, permits and the rebate path, line by line, with our price.

### Install

Permits first, then the work: usually two to five working days on site.

### Commissioning

Pressure test, vacuum, charge by weight, airflow and controls set before we call it done.

## Neighborhoods, landmarks and routes

- Newton Centre
- Newtonville
- West Newton
- Auburndale
- Waban
- Newton Highlands
- Newton Upper Falls
- Newton Lower Falls
- Chestnut Hill
- Nonantum
- Oak Hill
- Newton Corner

### Landmarks

- Crystal Lake
- Hammond Pond
- Echo Bridge
- Heartbreak Hill
- Newton City Hall and War Memorial

### Getting around

- Massachusetts Turnpike
- Route 9
- Commonwealth Avenue
- Route 128
- Washington Street

[Open Newton, MA in Google Maps](https://www.google.com/maps/search/?api=1&query=Newton%2C%20MA)

## Newton: questions

### Does Newton's fossil-fuel-free ordinance apply to my furnace replacement?

Not to an ordinary replacement. The ordinance, in effect since January 1, 2025, covers new buildings and major renovations. If you're only replacing a furnace, gas backup is still an option; if the job is part of a major renovation, the new heat is electric. We confirm which case yours is with Inspectional Services.

### What does a ducted heat pump cost in a Newton colonial?

On ducts we can reuse, our typical range is $15,000 to $28,000 and up before rebates. Where the second floor needs new ducts from an attic air handler, our typical range is $20,000 to $40,000 and up. The written estimate after the visit sets the price.

### Can I get the Mass Save whole-home rebate for replacing gas heat in Newton?

Yes, when the gas system is removed or disconnected, the equipment is cold-climate listed, the installer is in Mass Save's network and the house has proof of weatherization. Newton's gas comes from National Grid, which sponsors the rebate for gas-heated homes.

### How cold does the design night get in Newton?

Colder than at Logan. Newton sits inland between the airport and Hanscom Field, which averages about five nights a year at or below 0°F against under one at Logan. We run the load calculation at the local design temperature and pick equipment by its capacity at 5°F.

### Is there a noise limit for heat pumps in Newton?

Newton's own limit for outdoor units is confirmed per address. The state noise policy treats a source more than 10 dB(A) above background as a problem, so we choose the unit and its spot with the neighbor's windows in mind.

## Nearby service areas

- [Service area**Watertown** Ducted heat pumps for Watertown two-families and single homes, one system per unit, on Eversource with Mass Save rebates and dual fuel still allowed.](https://clementbostonheatpumps.com/service-areas/watertown/)
- [Service area**Waltham** Ducted heat pumps for Waltham ranches, colonials, two-families and condos, sized for inland cold, with Eversource rebates and gas backup still allowed.](https://clementbostonheatpumps.com/service-areas/waltham/)
- [Service area**Needham** Ducted heat pumps for Needham's larger colonials and capes, zoned floor by floor, with sheet metal and electrical permits filed online and Mass Save rebates.](https://clementbostonheatpumps.com/service-areas/needham/)

## Guides for houses in Newton

- [Decision Guide**Should I replace my gas furnace with a heat pump in Massachusetts?** Gas is cheap heat per unit, so this comparison turns on cooling, rebates, the age of the furnace and town rules, not the fuel bill alone.](https://clementbostonheatpumps.com/guide/heat-pump-vs-gas-furnace-massachusetts/)
- [Decision Guide**Will a heat pump work in an old house?** Boston has one of the oldest housing stocks in the country. Age changes how a heat pump goes in, not whether it can heat the house.](https://clementbostonheatpumps.com/guide/heat-pumps-in-old-houses/)
- [Learn**What size heat pump do I need?** Why square footage and the old unit's tonnage both mislead, what a room-by-room load calculation measures, and how the result turns into equipment.](https://clementbostonheatpumps.com/guide/heat-pump-sizing/)
- [Learn**How do Mass Save heat pump rebates work?** The three rebate tiers, the conditions behind each, the dates that change them, and what happens in towns with their own light plant.](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/)
- [Cost Guide**How much does heat pump installation cost in Massachusetts?** Our typical ranges for Boston-area ducted heat pump jobs, what's inside the price, and what rebates do to it.](https://clementbostonheatpumps.com/guide/heat-pump-installation-cost-massachusetts/)

## Get an estimate in Newton

Tell us what heats the house now and which rooms aren't working in Newton.

(857) 837-1475
