# Ducted heat pumps for Medford two-families and houses

> Ducted heat pumps for Medford two-families and single-families, with gas backup still allowed, the specialized energy code and National Grid rebates.

URL: https://clementbostonheatpumps.com/service-areas/medford/

Service area, Massachusetts

Ducted heat pumps for Medford two-families and single-families, with gas backup still allowed, the specialized energy code and National Grid rebates.

(857) 837-1475

Last Updated: November 12, 2026

Electric

National Grid

Rebates

Mass Save

Permits

Medford Building Department

Energy code

Specialized stretch code since July 1, 2024

## Inside a West Medford two-family heat pump split

Two outdoor units on stands at opposite rear corners of the two-family

Heat pump air handler in the attic where the old gas furnace stood

### Two furnaces, two ages

A 1920s West Medford two-family has a gas furnace for each floor. The first-floor furnace in the basement is six years old; the second-floor furnace in the attic is 24, and its air conditioner is failing. Replacing both the same way means scrapping a nearly new furnace.

### A different answer per floor

Upstairs, a 2-ton cold-climate air handler replaces the attic furnace on the existing ceiling ducts after a leakage test, and that floor goes all-electric. Downstairs, a 2-ton heat pump coil sits on the newer furnace, which takes over only below a changeover temperature set in the controls.

### Why Medford allows it

Medford follows the specialized code but isn't a fossil-fuel-free town, so gas backup is still allowed. The two floors land on different Mass Save tiers: whole-home upstairs, partial-home downstairs. Two outdoor units sit on stands at opposite rear corners of the narrow lot, spaced apart for sound, with local setback and sound rules confirmed for the address.

### Room to finish later

Permits for electrical, sheet metal and the capped attic gas line go through CitizenServe. When the first-floor furnace eventually wears out, that floor can go all-electric on the heat pump already in place, with only the furnace to remove and the controls to reset. The owner gets cooling on both floors now and keeps the option open.

*Project facts*

| Service | Dual fuel downstairs, all-electric upstairs |
| --- | --- |
| Where | West Medford |
| House | 1920s up-down two-family, about 1,200 sq ft per unit |
| Before | Two gas furnaces, 6 and 24 years old |
| After | Two 2-ton heat pumps, one with gas backup |
| Price | $29,700 before rebates |
| Time on site | Six working days |

## What brings people to us in Medford

### Two furnaces of different ages

The newer one can stay as backup beside a heat pump; the older one comes out and its floor goes all-electric.

### A renovation that still wants gas

Medford is not a fossil-fuel-free town, so a renovation can keep a gas furnace for the coldest hours, within the specialized code's paths.

### A colonial with ducts downstairs only

The basement furnace's ducts stay for the first floor; an attic air handler reaches the bedrooms.

### An oil boiler in the basement

About one Medford home in seven burns oil, and those homes have the biggest running-cost change to gain.

Arlington, next door, keeps new gas equipment out of major renovations; Medford doesn’t. That leaves you a real choice, and [Clement Boston Heat Pumps](https://clementbostonheatpumps.com/) builds every heat pump installation in Medford, MA around it: all-electric, or a heat pump with gas backup.

Over a quarter of Medford homes are two-families, where each floor may have its own furnace or boiler. The two floors don’t have to make the same choice.

## All-electric or gas backup: deciding in Medford

The state named Medford a comparison community in its fossil-fuel-free program, so it reports permits for comparison but doesn’t restrict fuel. Both designs are open; the house decides.

|  | All-electric (whole-home) | Heat pump with gas backup (dual fuel) |
| --- | --- | --- |
| Old equipment | Removed or disconnected | Furnace stays for the coldest hours |
| Mass Save tier | Whole-home, the larger rebate | Partial-home, needs integrated controls |
| Best fit | Old furnace, good ducts, tight house | Newer furnace, larger heat loss |
| Gas bill | Ends, if nothing else uses gas | Small, winter only |

### When dual fuel makes sense

A furnace that’s only a few years old still has a long life ahead. Keeping it as backup, with controls that hand off to gas below a set outdoor temperature, lets the heat pump carry most of the season. See [dual fuel heat pumps](https://clementbostonheatpumps.com/dual-fuel-heat-pump/).

### When all-electric wins

A furnace near the end of its life is the natural moment to go all-electric, and the whole-home rebate pays more. We size the heat pump to hold the house at design temperature without leaning on strips; see [whole-home heat pumps](https://clementbostonheatpumps.com/whole-home-heat-pump/).

### The specialized code

Medford adopted the specialized stretch code on July 1, 2024. It steers new homes and major renovations toward all-electric or pre-wired designs but still allows mixed-fuel paths; a straight replacement is unaffected.

## Two-families, floor by floor

Medford’s housing is about 34% detached and 27% two-family, with nearly half built before 1940. When a two-family has two furnaces of different ages, a split decision can make sense.

### The first floor

The basement furnace and its ducts serve the first floor. If the furnace is newer, a heat pump coil and outdoor unit pair with it as a dual-fuel system, and the ducts stay.

### The second floor

The upstairs unit’s furnace may sit in the attic, or the floor may run on a boiler. An [attic air handler](https://clementbostonheatpumps.com/attic-air-handler-heat-pump/) heat pump replaces it outright, with short insulated branches through the ceilings.

### Two units, two decisions

Each floor has its own thermostat, its own circuits and its own rebate paperwork. One owner can go all-electric while the other keeps gas. The [thermostat guide](https://clementbostonheatpumps.com/guide/heat-pump-thermostat/) explains how dual-fuel controls choose between the two.

## Single-family houses and three-deckers

The rest of Medford’s stock runs from colonials in West Medford and Lawrence Estates to a smaller number of three-deckers near Medford Square and South Medford.

### Colonials with partial ducts

A colonial whose basement furnace feeds the first floor well and the bedrooms poorly gets two zones: the downstairs ducts stay, and an attic unit takes the second floor. See [furnace to heat pump](https://clementbostonheatpumps.com/furnace-to-heat-pump-conversion/).

### Three-deckers

About 7% of Medford homes sit in three- or four-unit buildings. Each floor gets its own system; the [three-decker guide](https://clementbostonheatpumps.com/guide/triple-decker-heat-pumps/) covers the middle floor.

## Two outdoor units on one lot

A two-family with a system per floor needs two outdoor units, and Medford lots are rarely wide. Where they go is worth settling before the equipment is chosen.

### Spacing and sound

Medford’s own setback or sound limit for outdoor units is confirmed per address. The state noise policy treats a source more than 10 dB(A) above background as a problem, so we compare each unit’s rated sound with the distance to the nearest neighbor’s window and keep the pair apart rather than side by side.

### Height and access

Each unit sits on a stand above the drift line, with clear space for airflow and for service. Line sets run along the foundation to each floor’s air handler, one up the side wall to the attic and one into the basement. Our [snow stand guide](https://clementbostonheatpumps.com/guide/heat-pump-snow-stand/) covers clearances.

### Sizing for the right night

Medford sits a little inland of Boston, between the harbor and the Fells. Each floor’s load is calculated room by room at the local design temperature, and equipment is chosen by its output at 5°F rather than its rated size.

## Fuel, rates and running cost

Gas heats about 62% of Medford homes, electricity about 19% and oil about 15%. National Grid supplies both electricity and gas, so it sponsors the Mass Save rebate whichever fuel you leave.

### Oil homes

Oil costs more per unit of heat than a heat pump on National Grid’s winter rate. Those homes have the clearest running-cost case; see [oil to heat pump](https://clementbostonheatpumps.com/oil-to-heat-pump-conversion/).

### Gas homes

Gas costs less per unit of heat than a heat pump on National Grid’s rate, which is why dual fuel suits some Medford houses. The [gas furnace guide](https://clementbostonheatpumps.com/guide/heat-pump-vs-gas-furnace-massachusetts/) works through the numbers, and the [backup heat guide](https://clementbostonheatpumps.com/guide/heat-pump-aux-heat/) explains the switchover point.

## Code and rebate rules that apply in Medford

Medford’s Building Department takes applications through its online CitizenServe portal: electrical and sheet metal for a ducted job, gas where a line is capped or a furnace stays.

| What | The Medford picture |
| --- | --- |
| Permit portal | CitizenServe |
| Energy code | Specialized stretch code since July 1, 2024 |
| Fossil-fuel-free program | Comparison community; gas backup allowed |
| Electric and gas utility | National Grid |
| Built before 1940 | 48.8% |

National Grid’s seasonal rate lowers winter distribution charges for homes that heat with a heat pump. Our [rebate guide](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/) lists the whole-home and partial-home conditions.

## How the work runs on a Medford job

The visit works floor by floor: heat loss room by room, the age and condition of each furnace or boiler, the ducts, the panel, and a spot for each outdoor unit.

- **Two options on paper** where it’s close: an all-electric price and a dual-fuel price, each with its rebate tier.
- **Permits** through CitizenServe, then three to seven working days on site per floor.
- **Controls set** so a dual-fuel floor hands off to gas at the temperature in the estimate.
- **Commissioning:** pressure test, vacuum, refrigerant by weight, airflow and static measured, lockout recorded.

[Somerville](https://clementbostonheatpumps.com/service-areas/somerville/) and [Malden](https://clementbostonheatpumps.com/service-areas/malden/) border Medford to the south and east; [Arlington](https://clementbostonheatpumps.com/service-areas/arlington/) to the west runs the fossil-fuel-free by-law.

## Services in Medford

- [Service**Dual fuel heat pumps** A heat pump paired with the furnace you keep, with one control deciding which one heats.](https://clementbostonheatpumps.com/dual-fuel-heat-pump/)
- [Service**Furnace to heat pump conversion** Take out the gas or propane furnace and heat and cool through the same ducts with a heat pump.](https://clementbostonheatpumps.com/furnace-to-heat-pump-conversion/)
- [Service**Whole-home heat pumps** One ducted system that heats and cools the whole house, with the furnace or boiler retired.](https://clementbostonheatpumps.com/whole-home-heat-pump/)
- [Service**Attic air handlers** An attic air handler that heats and cools the upper floor, with short sealed ducts and a guarded drain.](https://clementbostonheatpumps.com/attic-air-handler-heat-pump/)
- [Service**Oil to heat pump conversion** Retire the oil furnace or hydro-air boiler, cap the oil line and heat and cool through the ducts you have.](https://clementbostonheatpumps.com/oil-to-heat-pump-conversion/)
- [Service**Heat pump replacement** A new ducted heat pump in place of one at the end of its life, sized again from the house.](https://clementbostonheatpumps.com/heat-pump-replacement/)

## How a job usually runs in Medford

### First call

You tell us what heats and cools the house now, which rooms aren't working, and roughly where the house is.

### Home visit

We measure the house for a load calculation, test the ducts, check the panel and look for an outdoor spot.

### Written estimate

Equipment, duct changes, electrical, permits and the rebate path, line by line, with our price.

### Install

Permits first, then the work: usually two to five working days on site.

### Commissioning

Pressure test, vacuum, charge by weight, airflow and controls set before we call it done.

## Neighborhoods, landmarks and routes

- West Medford
- Medford Square
- Fulton Heights
- Wellington
- South Medford
- Lawrence Estates
- Medford Hillside
- North Medford
- Glenwood

### Landmarks

- Middlesex Fells Reservation
- Mystic River
- Tufts University
- Royall House
- Wellington station

### Getting around

- Interstate 93
- Mystic Valley Parkway
- Route 60
- Route 38
- Fellsway

[Open Medford, MA in Google Maps](https://www.google.com/maps/search/?api=1&query=Medford%2C%20MA)

## Medford: questions

### Can I keep my gas furnace as backup with a heat pump in Medford?

Yes. Medford is a comparison community in the state's fossil-fuel-free program, not a participant, so a heat pump with gas backup is still allowed, including in renovations, within the specialized code's paths. Mass Save pays its partial-home rebate when the two are run by integrated controls.

### What does a heat pump cost for a Medford two-family?

Each floor is its own system. On ducts we can reuse, our typical range is $15,000 to $28,000 and up before rebates; with new ductwork, $20,000 to $40,000 and up. A two-family with one dual-fuel floor and one all-electric floor is priced line by line after the visit.

### Which rebate is bigger in Medford, whole-home or dual fuel?

Whole-home, which pays $2,650 per ton up to $8,500 for installs through the end of 2026 when the old system is removed. Partial-home, for a heat pump with integrated gas backup, pays $1,125 per ton up to the same cap. Both drop from January 1, 2027.

### How do I apply for a Medford heat pump permit?

Medford takes permit applications through its online CitizenServe portal. A ducted heat pump job needs an electrical permit and a sheet metal permit, plus a gas permit when a line is capped, filed by the licensed trades doing the work.

### Does Medford's specialized code apply to replacing my furnace?

No. Medford has followed the specialized stretch code since July 1, 2024, but it governs new construction and major renovations. A like-for-like furnace or heat pump replacement in an existing house is unaffected.

## Nearby service areas

- [Service area**Somerville** Ducted heat pumps for Somerville two-families, three-deckers and condos, planned floor by floor, with sheet metal permits and gas backup still allowed.](https://clementbostonheatpumps.com/service-areas/somerville/)
- [Service area**Malden** Ducted heat pumps for Malden homes on electric baseboard, gas or oil, from Maplewood capes to Edgeworth two-families, with National Grid rebates and rates.](https://clementbostonheatpumps.com/service-areas/malden/)
- [Service area**Arlington** Ducted heat pumps for Arlington renovations under the fossil-fuel-free by-law and the specialized code, in bungalows, two-families and Heights colonials.](https://clementbostonheatpumps.com/service-areas/arlington/)

## Guides for houses in Medford

- [Learn**Why does my heat pump's aux heat keep coming on?** Backup heat is part of every cold-climate system. Here's when it should run, when it shouldn't, and the settings that decide which.](https://clementbostonheatpumps.com/guide/heat-pump-aux-heat/)
- [Decision Guide**Should I replace my gas furnace with a heat pump in Massachusetts?** Gas is cheap heat per unit, so this comparison turns on cooling, rebates, the age of the furnace and town rules, not the fuel bill alone.](https://clementbostonheatpumps.com/guide/heat-pump-vs-gas-furnace-massachusetts/)
- [Learn**What thermostat do I need for a heat pump, and how should I set it?** The control decides whether a heat pump runs on its compressor or on expensive backup heat. Here's what it has to do and how to set it for a Massachusetts winter.](https://clementbostonheatpumps.com/guide/heat-pump-thermostat/)
- [Decision Guide**How do you put heat pumps in a triple-decker?** Three stacked homes under one roof, often with three owners, three meters and one narrow side yard. Here's how a heat pump job works around that.](https://clementbostonheatpumps.com/guide/triple-decker-heat-pumps/)
- [Learn**How do Mass Save heat pump rebates work?** The three rebate tiers, the conditions behind each, the dates that change them, and what happens in towns with their own light plant.](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/)

## Get an estimate in Medford

Tell us what heats the house now and which rooms aren't working in Medford.

(857) 837-1475
