# Heat pumps for Medfield, MA colonials leaving oil or propane

> Ducted heat pumps for Medfield colonials heated by oil or propane, compared honestly against a gas conversion, with Eversource rebates and winter rates.

URL: https://clementbostonheatpumps.com/service-areas/medfield/

Service area, Massachusetts

Ducted heat pumps for Medfield colonials heated by oil or propane, compared honestly against a gas conversion, with Eversource rebates and winter rates.

(857) 837-1475

Last Updated: November 12, 2026

Electric

Eversource

Rebates

Mass Save

Permits

Town of Medfield building department

Energy code

Stretch energy code since January 1, 2017

## Inside a Medfield oil-to-heat-pump decision

New sealed, insulated attic ducts on the second-floor heat pump

Two heat pump outdoor units on stands behind a hedge at the side of the house

### Gas or heat pump

A 1996 colonial near Medfield Center has a 26-year-old oil furnace for the first floor, an attic AC for the second, and a gas main in the street. The owners price both. Gas needs a service line, a new furnace and venting, and still leaves an old AC upstairs.

### Two floors, two systems

The load comes to 41,200 BTU an hour at the design temperature, split about 55/45 by floor. Each floor already has its own ducts, so a 2.5-ton heat pump takes the furnace's spot on the basement plenum and a 2-ton unit replaces the attic AC air handler.

### Fixing the attic

The attic flex leaks into the cold space, so about 60 feet comes out and sealed, R-8 insulated duct goes in. The attic air handler sits on a platform with a secondary pan. Both outdoor units go on stands behind a side hedge, on 24- and 38-foot line sets.

### Finishing

Each circuit passes a nitrogen test, a vacuum below 500 microns and a charge by weight, and each floor's airflow is measured. The 275-gallon tank comes out under the fire department's permit, and the Mass Save whole-home rebate runs through Eversource as the electric sponsor.

*Project facts*

| Service | Whole-home heat pump replacing oil heat and attic AC |
| --- | --- |
| Where | Medfield Center area |
| House | 1996 two-story colonial, about 3,000 sq ft |
| Before | 26-year-old oil furnace, attic AC, leaking attic flex |
| After | Two heat pumps, 2.5 and 2 tons |
| Price | $27,600 before rebates, tank removal included |
| Time on site | Five working days |

## What brings people to us in Medfield

### An oil furnace on a street with a gas main

Converting to gas means a new service line and a new furnace. A heat pump reuses the ducts and skips the gas hookup.

### A colonial with a basement furnace and an attic AC

Two heat pumps, one for each floor, replace both systems on the ducts each floor already has.

### A propane house beyond the gas main

Propane costs more per unit of heat than gas, and Mass Save's whole-home rebate covers replacing it.

Plenty of Medfield streets have a gas main under them and oil tanks in the basements beside them. If yours is one, you have three choices when the oil furnace wears out: convert to gas, switch to a heat pump, or run both.

[Clement Boston Heat Pumps](https://clementbostonheatpumps.com/) handles heat pump installation in Medfield, MA, and we lay the three side by side before recommending one. About one Medfield home in four still burns oil, and roughly one in twenty runs on propane.

## Gas, heat pump, or both?

Each option solves the oil problem differently. The right one depends on your ducts, your panel, whether you want central cooling, and how long you plan to stay.

| Option | What it takes | What you end up with |
| --- | --- | --- |
| Convert to gas | Gas service line, new furnace, new venting | Gas heat; cooling stays separate |
| Whole-home heat pump | Air handler on your ducts, outdoor unit | Heating and cooling from one system |
| Dual fuel | Heat pump plus a gas furnace for the coldest nights | Two systems, smaller rebate |

A gas conversion trades one fuel bill for another and puts new money into equipment that only heats. A heat pump replaces the AC too, and Mass Save’s whole-home rebate covers it. See [oil to heat pump conversion](https://clementbostonheatpumps.com/oil-to-heat-pump-conversion/) and our [heat pump vs gas furnace guide](https://clementbostonheatpumps.com/guide/heat-pump-vs-gas-furnace-massachusetts/).

### When dual fuel fits

If the house is large, loosely built, or you simply want a flame for the coldest nights, a heat pump with a gas furnace as backup works. A listed integrated control hands off at a set outdoor temperature, and Mass Save’s partial-home tier pays a smaller rebate. See [dual-fuel heat pumps](https://clementbostonheatpumps.com/dual-fuel-heat-pump/).

## What each choice costs to run

Per unit of heat delivered, oil is the most expensive fuel in Massachusetts, then propane. A heat pump on Eversource’s winter rate lands well below both, and gas remains the cheapest.

### Against oil and propane

Leaving oil or propane for a heat pump lowers the heating bill in most houses, and the summer cooling comes from the same equipment. Our [heat pump vs oil guide](https://clementbostonheatpumps.com/guide/heat-pump-vs-oil-heat/) shows how the numbers are built.

### Against gas

Gas beats a heat pump per unit of heat on most days. The case for skipping it rests on avoiding the service line and furnace cost, getting cooling, and the larger rebate. We put both running costs in the estimate on your own rates.

## Medfield colonials, and where the air handlers go

A typical Medfield colonial has a basement furnace feeding the first floor and an AC air handler in the attic for the second. That layout makes a two-system heat pump plan natural.

### Two floors, two systems

The basement air handler takes the furnace’s place on the existing plenum. The attic unit replaces the AC air handler on a platform with a secondary drain pan. Each is sized for its own floor, because the upper floor loses more heat through the roof. See [attic air handlers](https://clementbostonheatpumps.com/attic-air-handler-heat-pump/).

### Before we reuse the ducts

We measure static pressure, check return size and look for leaks in the attic, where a leak pulls cold air into the house all winter. Leaking flex gets replaced with sealed, insulated duct.

### Older houses near the center

Fewer than one Medfield home in eight predates 1940. Where one heats with a boiler and has no ducts, closets that stack between floors carry a trunk, or a small-duct system threads through the walls.

## Sizing in a town this far inland

Medfield sits about 17 miles from downtown Boston, along the Charles, and its winter nights run colder than the city’s. We size every system for that.

A room-by-room Manual J load calculation at your town’s design temperature sets the size. Equipment is chosen by its capacity at 5°F, and backup heat locks out above a set temperature. Our [sizing guide](https://clementbostonheatpumps.com/guide/heat-pump-sizing/) explains each step.

## Cooling the second floor

Eight in ten Medfield homes are detached houses, and in a two-story colonial the upstairs bedrooms are where summer heat collects. An attic AC that struggles in July is a common reason to start this conversation.

A heat pump in the attic does the cooling that AC did, with variable speed that runs longer at low output and pulls more moisture out of the air. The same unit heats the floor in winter. Our [heat pump vs central AC guide](https://clementbostonheatpumps.com/guide/heat-pump-vs-central-ac/) compares the two.

## Propane homes off the gas main

About 5% of Medfield homes heat with propane, usually where there’s no gas main. Propane costs more per unit of heat than gas, so the running-cost case is strong.

Extending a gas main to those streets isn’t an option you control, so the real choice is propane or electric. The propane company reclaims its own tank once the heat pump is carrying the house.

### Same plan, same rebate

A propane furnace on ducts makes the same two-system plan as oil. Mass Save covers propane replacement on the same terms as oil; our [rebate guide](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/) lists the conditions.

## The paperwork in Medfield

The Town of Medfield’s building department issues the permits. The filing route, fees and any local noise rules are confirmed per address when we apply.

| What | The Medfield answer |
| --- | --- |
| Permits | Town building department: electrical, sheet metal, gas where capped |
| Energy code | Stretch code since January 1, 2017 |
| Electric utility | Eversource |
| Gas utility | Eversource Gas |
| Rebate program | Mass Save |
| Winter heat pump rate | Eversource, November 1 to April 30 |

Eversource’s [winter heat pump rate](https://clementbostonheatpumps.com/guide/heat-pump-electric-rate-massachusetts/) lowers distribution and transmission charges on all household kilowatt-hours through the heating season.

## Your first visit, and what follows

We start with the load calculation and the ducts, then the panel, the tank and the outdoor spot.

- **Written estimate:** equipment with its capacity at 5°F, duct changes, electrical, tank, permits, rebate path and price.
- **Install:** four to six working days for a two-system house on existing ducts.
- **Tank:** removed after the heat pump carries the house, for $600 to $1,500 when it’s accessible.
- **Proving it works:** both refrigerant circuits pass a nitrogen test and a vacuum under 500 microns, get charged by weight, and each floor’s airflow and static are read. The backup heat lockout goes on the start-up record, and the thermostats are set up with you before we leave.

[Walpole](https://clementbostonheatpumps.com/service-areas/walpole/) shares Medfield’s utilities and its oil-heavy mix; [Westwood](https://clementbostonheatpumps.com/service-areas/westwood/) sits closer in on Eversource.

## Services in Medfield

- [Service**Oil to heat pump conversion** Retire the oil furnace or hydro-air boiler, cap the oil line and heat and cool through the ducts you have.](https://clementbostonheatpumps.com/oil-to-heat-pump-conversion/)
- [Service**Whole-home heat pumps** One ducted system that heats and cools the whole house, with the furnace or boiler retired.](https://clementbostonheatpumps.com/whole-home-heat-pump/)
- [Service**Attic air handlers** An attic air handler that heats and cools the upper floor, with short sealed ducts and a guarded drain.](https://clementbostonheatpumps.com/attic-air-handler-heat-pump/)
- [Service**Dual fuel heat pumps** A heat pump paired with the furnace you keep, with one control deciding which one heats.](https://clementbostonheatpumps.com/dual-fuel-heat-pump/)
- [Service**Furnace to heat pump conversion** Take out the gas or propane furnace and heat and cool through the same ducts with a heat pump.](https://clementbostonheatpumps.com/furnace-to-heat-pump-conversion/)
- [Service**Oil tank removal** The old basement tank pumped, cleaned, removed and permitted once the heat pump is running.](https://clementbostonheatpumps.com/oil-tank-removal/)

## How a job usually runs in Medfield

### First call

You tell us what heats and cools the house now, which rooms aren't working, and roughly where the house is.

### Home visit

We measure the house for a load calculation, test the ducts, check the panel and look for an outdoor spot.

### Written estimate

Equipment, duct changes, electrical, permits and the rebate path, line by line, with our price.

### Install

Permits first, then the work: usually two to five working days on site.

### Commissioning

Pressure test, vacuum, charge by weight, airflow and controls set before we call it done.

## Neighborhoods, landmarks and routes

- Medfield Center

### Landmarks

- Charles River
- Rocky Woods Reservation
- Noon Hill Reservation
- Medfield State Hospital grounds

### Getting around

- Route 109
- Route 27
- Main Street
- North Street

[Open Medfield, MA in Google Maps](https://www.google.com/maps/search/?api=1&query=Medfield%2C%20MA)

## Medfield: questions

### Should I convert my Medfield oil furnace to gas or to a heat pump?

It depends on your street and your ducts. Gas needs a service line and a new furnace and keeps a fuel bill; a heat pump reuses the ducts, adds central cooling and qualifies for Mass Save's whole-home rebate through Eversource. We price your house both ways when you ask.

### What does a whole-home heat pump cost in a Medfield colonial?

On ducts we can reuse, our typical range is $15,000 to $28,000 and up before rebates; two systems for a larger two-story house sit toward the top. Removing an accessible oil tank adds $600 to $1,500. The written estimate after the visit sets your price.

### Does Mass Save pay to replace propane heat in Medfield?

Yes. Propane is one of the fuels Mass Save's whole-home rebate covers replacing, with Eversource as your electric sponsor. The rebate also needs cold-climate listed equipment, an installer in Mass Save's network, the old system removed and proof of weatherization.

### Who handles building permits for a Medfield heat pump?

The Town of Medfield's building department. A ducted heat pump needs an electrical permit and a sheet metal permit for the ducts, plus a gas permit where a line is capped. The filing route, fees and any noise rules are confirmed per address.

### Is Medfield on the stretch or the specialized energy code?

The stretch code, since January 1, 2017. Medfield has not adopted the specialized code, so new homes and major renovations can still be designed with fossil fuel equipment. A heating replacement in an existing house isn't affected by either.

## Nearby service areas

- [Service area**Walpole** Oil-to-heat-pump conversions for Walpole homes on Eversource, reusing furnace ducts where they measure up, with tank removal and panel work in one plan.](https://clementbostonheatpumps.com/service-areas/walpole/)
- [Service area**Westwood** Ducted heat pumps for Westwood homes on oil or propane, with Eversource on both meters, Mass Save's whole-home rebate, tank removal and the winter rate.](https://clementbostonheatpumps.com/service-areas/westwood/)
- [Service area**Needham** Ducted heat pumps for Needham's larger colonials and capes, zoned floor by floor, with sheet metal and electrical permits filed online and Mass Save rebates.](https://clementbostonheatpumps.com/service-areas/needham/)

## Guides for houses in Medfield

- [Decision Guide**Is a heat pump better than oil heat in Massachusetts?** Running cost worked out from Massachusetts fuel prices and winter heat pump rates, plus the comfort, cooling, tank and hot water questions that come with the switch.](https://clementbostonheatpumps.com/guide/heat-pump-vs-oil-heat/)
- [Decision Guide**Should I replace my gas furnace with a heat pump in Massachusetts?** Gas is cheap heat per unit, so this comparison turns on cooling, rebates, the age of the furnace and town rules, not the fuel bill alone.](https://clementbostonheatpumps.com/guide/heat-pump-vs-gas-furnace-massachusetts/)
- [Learn**What size heat pump do I need?** Why square footage and the old unit's tonnage both mislead, what a room-by-room load calculation measures, and how the result turns into equipment.](https://clementbostonheatpumps.com/guide/heat-pump-sizing/)
- [Learn**How do Mass Save heat pump rebates work?** The three rebate tiers, the conditions behind each, the dates that change them, and what happens in towns with their own light plant.](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/)
- [Learn**How long does a heat pump last?** No one can promise a heat pump a number of years. What you can control is the install, the sizing and the upkeep that decide most of it.](https://clementbostonheatpumps.com/guide/heat-pump-lifespan/)

## Get an estimate in Medfield

Tell us what heats the house now and which rooms aren't working in Medfield.

(857) 837-1475
