# Heat pumps for Everett two-families, one system per floor

> Ducted heat pumps for Everett two- and three-families moving off oil or gas boilers, with one system per unit and National Grid's winter heat pump rate.

URL: https://clementbostonheatpumps.com/service-areas/everett/

Service area, Massachusetts

Ducted heat pumps for Everett two- and three-families moving off oil or gas boilers, with one system per unit and National Grid's winter heat pump rate.

(857) 837-1475

Last Updated: November 12, 2026

Electric

National Grid

Rebates

Mass Save

Permits

City of Everett building department

Energy code

Stretch energy code since July 1, 2015

## What an oil-to-heat-pump job in a Glendale two-family looks like

Basement air handler and trunk for the first-floor unit

Second outdoor unit on the rear porch roof

### One boiler, two households

A 1915 two-family in Glendale runs one oil boiler and one hot-water loop for both floors, on a single thermostat. Each floor cools with window units. The owner, on the first floor, wants to stop buying oil and give each household its own heat, cooling and electric bill.

### A system for each floor

The first floor gets a 2-ton air handler in the basement with six floor registers and a central return. The second floor gets a 2-ton horizontal unit in the low attic, with insulated branches to six ceiling registers. Neither route touches the plaster walls between the floors.

### Two units, one small yard

The rear yard has room for one outdoor unit on a stand. The second goes on the rear porch roof, on a rated stand after the framing is checked, with its 36-foot line set run down the back wall in a cover. Each system runs from its own unit's 100-amp panel.

### Keeping both floors warm

The attic system goes in first while the boiler still heats the house, then the basement system. Only then do the boiler and 275-gallon tank come out. National Grid sponsors Mass Save on both sides, so each system carries its own rebate application, and the winter heat pump rate applies to each meter.

*Project facts*

| Service | Oil to heat pump conversion, one system per unit |
| --- | --- |
| Where | Glendale, Everett |
| House | 1915 two-family, about 1,100 sq ft per floor |
| Before | Shared oil boiler and radiators, window AC |
| After | 2-ton basement and 2-ton attic heat pumps |
| Price | $38,600 for both systems before rebates |
| Time on site | Eight working days |

## What brings people to us in Everett

### One oil boiler heating two apartments

Splitting the heat into one ducted system per floor gives each household its own thermostat and its own electric bill.

### A gas boiler near the end

Most Everett homes heat with gas. Mass Save's whole-home rebate covers replacing it when the old system comes out.

### A three-decker with no yard to spare

Outdoor units go on a rear porch roof, a flat roof or wall brackets, with line sets run up the back of the building.

### Window units and radiators

Ducted air handlers in the basement, a closet or the attic bring central cooling to floors that have only had window units.

The oil boiler in an Everett two-family usually heats both floors through one set of pipes, and replacing it raises questions a single-family never faces. [Clement Boston Heat Pumps](https://clementbostonheatpumps.com/) handles heat pump installation in Everett, MA by giving each floor its own ducted system.

That split decides almost everything else: where each air handler sits, how two outdoor units fit on a small lot, and how the rebates are counted.

## Why Everett jobs are planned floor by floor

More than half of Everett’s homes are in two-families and three-deckers, and more than half were built before 1940. A single system can’t serve two households well, so we plan one per unit.

### Each floor loses heat differently

The top floor loses heat through the roof, the first floor through the basement and the sills. A load calculation for each unit, room by room, sizes each system for its own floor instead of splitting one number in half. Our [three-decker guide](https://clementbostonheatpumps.com/guide/triple-decker-heat-pumps/) walks through the method.

### Where each air handler goes

The first floor’s unit hangs in the basement and feeds floor registers. The top floor’s goes in the attic and feeds ceiling registers. A middle floor gets a closet unit or a small-duct system that runs through the floor joists above. See [boiler and radiator homes](https://clementbostonheatpumps.com/boiler-to-heat-pump-conversion/).

### Two units, one small lot

Everett lots leave little side yard. We favor rear yards and rear porch roofs, and bracket units to a back wall where the ground is taken. The city’s noise and setback rules are confirmed per address before we set anything.

## Oil, gas and the National Grid winter rate

About two in three Everett homes heat with gas, 18% with electricity and 12% with oil. The oil homes have the strongest running-cost case, and National Grid’s seasonal rate helps every group.

### If your boiler burns oil

Oil is the most expensive common heating fuel per delivered BTU. A cold-climate heat pump on the winter rate costs less to run, and the deliveries stop. We remove the basement tank at the same time; see [oil to heat pump conversion](https://clementbostonheatpumps.com/oil-to-heat-pump-conversion/) and [oil tank removal](https://clementbostonheatpumps.com/oil-tank-removal/).

### If your boiler burns gas

Gas costs less per BTU than oil, so the savings are smaller. Most gas owners switch because the boiler is near the end, or because they want central cooling on every floor. Our [heat pump vs boiler guide](https://clementbostonheatpumps.com/guide/heat-pump-vs-boiler/) compares the two.

### What the winter rate does

National Grid’s optional heat pump rate cuts the distribution charge on every household kilowatt-hour from November 1 to April 30. Transmission and supply stay the same. See our [winter rate guide](https://clementbostonheatpumps.com/guide/heat-pump-electric-rate-massachusetts/).

## Old houses, and routes for new ducts

Everett’s pre-1940 houses have plaster walls, balloon framing and boilers that never needed ducts. The work is finding routes that don’t open finished rooms.

- **Basement first:** the first floor is the easy one. The trunk runs between joists, registers go in the floor, and the return sits in a central hall.
- **Attic for the top floor:** a low attic takes a compact horizontal air handler and short insulated branches to ceiling registers.
- **Closets and chases:** stacked closets carry trunks between floors when a unit needs a second route. Old chimneys sometimes help, once lined or abandoned.
- **Small-duct systems:** where none of that works, 2-inch flexible tubes fit through spaces a standard duct can’t. Our [old house guide](https://clementbostonheatpumps.com/guide/heat-pumps-in-old-houses/) covers them.

### Panels in older two-families

Many Everett two-families still have a 100-amp service per unit. A ducted heat pump often fits on it after a load calculation, and where it doesn’t, the service is upgraded first. See [panel upgrades for heat pumps](https://clementbostonheatpumps.com/electrical-panel-upgrade-for-heat-pump/).

## When the two floors don’t share one owner

Plenty of Everett two-families and three-deckers have been split into condos. Then each owner decides on their own system, and shared spaces need everyone’s agreement.

### Shared basements, attics and walls

The first-floor owner’s air handler in a shared basement, or a top-floor line set running down a common rear wall, touches property the other owners hold in common. We bring a placement drawing showing every penetration, line set and outdoor unit so the association can approve it once.

### One owner switching first

It’s common for one floor to go electric while the others stay on their own boilers for now. We plan the first system so it doesn’t block the others’ routes later: the trunk stays out of the shared chase, and the outdoor unit leaves room on the porch roof for a second. Our [condo guide](https://clementbostonheatpumps.com/guide/condo-heat-pump-replacement/) covers board approvals.

### Keeping the bills separate

One system per unit, on that unit’s own panel and meter, keeps each household’s heating cost on its own electric bill. Mixing circuits between units creates billing problems that are hard to undo.

## Rebates and permits, Everett edition

Everett’s building department issues the permits; its online route is confirmed per address. The job needs an electrical permit and the city’s mechanical permits for ducts and equipment.

| What | The Everett figure |
| --- | --- |
| Electric utility | National Grid |
| Gas utility | National Grid (Boston Gas) |
| Energy code | Stretch code since July 1, 2015; specialized code not adopted |
| Heating fuel | Gas 66.6%, electricity 18.1%, oil 12.0% |
| Housing | 25.7% two-unit, 26.8% three- or four-unit buildings |

Because National Grid sponsors Mass Save on both the electric and gas side, oil, baseboard and gas homes all have a rebate route. The whole-home tier pays $2,650 per ton up to $8,500 for installs through December 31, 2026; see the [rebate guide](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/).

Everett is also on the state’s coastal list, along the Mystic River and Malden River. Lower Broadway and the waterfront blocks get units set out of wind-driven spray.

## Start to finish in Everett

The first visit covers both units: a load calculation for each floor, duct routes, the panels and a spot for each outdoor unit.

1. **Written estimate per unit:** equipment and its capacity at 5°F, duct work, electrical, permits, tank removal and each unit’s rebate path.
2. **Sequencing:** the occupied floor stays heated while the other is switched, so a household is never without heat.
3. **Install:** usually five to nine working days for both floors with new ducts.
4. **Commissioning:** pressure test, vacuum below 500 microns, charge weighed for each line length, airflow and controls recorded.

The [cost guide](https://clementbostonheatpumps.com/guide/heat-pump-installation-cost-massachusetts/) sets out our ranges. [Malden](https://clementbostonheatpumps.com/service-areas/malden/) next door has much the same two-family stock, and [Chelsea](https://clementbostonheatpumps.com/service-areas/chelsea/) shares the Mystic waterfront.

## Services in Everett

- [Service**Oil to heat pump conversion** Retire the oil furnace or hydro-air boiler, cap the oil line and heat and cool through the ducts you have.](https://clementbostonheatpumps.com/oil-to-heat-pump-conversion/)
- [Service**Boiler to heat pump conversion** New ducts or small-duct high-velocity runs so a heat pump can heat and cool a radiator house.](https://clementbostonheatpumps.com/boiler-to-heat-pump-conversion/)
- [Service**Heat pump ductwork** Duct testing, sealing, new returns and resized runs so a heat pump gets the air it needs.](https://clementbostonheatpumps.com/heat-pump-ductwork/)
- [Service**Attic air handlers** An attic air handler that heats and cools the upper floor, with short sealed ducts and a guarded drain.](https://clementbostonheatpumps.com/attic-air-handler-heat-pump/)
- [Service**Oil tank removal** The old basement tank pumped, cleaned, removed and permitted once the heat pump is running.](https://clementbostonheatpumps.com/oil-tank-removal/)

## How a job usually runs in Everett

### First call

You tell us what heats and cools the house now, which rooms aren't working, and roughly where the house is.

### Home visit

We measure the house for a load calculation, test the ducts, check the panel and look for an outdoor spot.

### Written estimate

Equipment, duct changes, electrical, permits and the rebate path, line by line, with our price.

### Install

Permits first, then the work: usually two to five working days on site.

### Commissioning

Pressure test, vacuum, charge by weight, airflow and controls set before we call it done.

## Neighborhoods, landmarks and routes

- Glendale
- Woodlawn
- Everett Square
- West Everett
- Lower Broadway
- Ferry Street area
- Hancock Street area

### Landmarks

- Glendale Park
- Encore Boston Harbor
- Mystic River waterfront
- Everett Square
- Woodlawn Cemetery

### Getting around

- Broadway (Route 99)
- Revere Beach Parkway (Route 16)
- Ferry Street
- Main Street

[Open Everett, MA in Google Maps](https://www.google.com/maps/search/?api=1&query=Everett%2C%20MA)

## Everett: questions

### What does a heat pump cost for an Everett two-family?

Each unit is its own system. In houses heated by a boiler with no ducts, our typical range is $20,000 to $40,000 and up per system before rebates, depending on duct routes and floor size. Where ducts can be reused, it is $15,000 to $28,000 and up. The written estimate sets the price.

### Is Everett on National Grid or Eversource for electricity?

National Grid supplies Everett's electricity and Boston Gas supplies its gas, per the state utility lookup. That makes National Grid your Mass Save sponsor and gives you its optional winter heat pump rate.

### Can each apartment in an Everett two-family get its own Mass Save rebate?

Mass Save's rebates are figured per system and per ton, so a two-family with two systems is planned unit by unit. Each system needs cold-climate listed equipment and the old heat disconnected for the whole-home tier. We lay out the path for each unit on the estimate.

### Where does the outdoor unit go on a tight Everett lot?

Rear yards, rear porch roofs, flat roofs and wall brackets are the usual places. Everett's local noise and setback rules are confirmed per address, and we keep units away from bedroom windows on the next lot.

### How does the National Grid heat pump rate lower an Everett bill?

From November 1 to April 30 it lowers the distribution charge on every kilowatt-hour your household uses, not just the heat pump's share. It doesn't change transmission or supply. Mass Save rebate recipients are usually enrolled automatically.

## Nearby service areas

- [Service area**Malden** Ducted heat pumps for Malden homes on electric baseboard, gas or oil, from Maplewood capes to Edgeworth two-families, with National Grid rebates and rates.](https://clementbostonheatpumps.com/service-areas/malden/)
- [Service area**Chelsea** Ducted heat pumps for Chelsea three-deckers and condos, one system per floor, with outdoor units fitted to tight lots and roofs on Eversource's winter rate.](https://clementbostonheatpumps.com/service-areas/chelsea/)
- [Service area**Medford** Ducted heat pumps for Medford two-families and single-families, with gas backup still allowed, the specialized energy code and National Grid rebates.](https://clementbostonheatpumps.com/service-areas/medford/)

## Guides for houses in Everett

- [Decision Guide**How do you put heat pumps in a triple-decker?** Three stacked homes under one roof, often with three owners, three meters and one narrow side yard. Here's how a heat pump job works around that.](https://clementbostonheatpumps.com/guide/triple-decker-heat-pumps/)
- [Learn**How does the heat pump electric rate work in Massachusetts?** Which part of your electric bill the seasonal rate lowers, why it applies to the whole house, how enrollment works, and what it means for the switch from oil or gas.](https://clementbostonheatpumps.com/guide/heat-pump-electric-rate-massachusetts/)
- [Decision Guide**Should I replace my boiler with a heat pump?** Radiator heat is comfortable and long-lived; a ducted heat pump adds cooling and drops the fuel. The ducts are what decide whether the switch is worth it.](https://clementbostonheatpumps.com/guide/heat-pump-vs-boiler/)
- [Decision Guide**Will a heat pump work in an old house?** Boston has one of the oldest housing stocks in the country. Age changes how a heat pump goes in, not whether it can heat the house.](https://clementbostonheatpumps.com/guide/heat-pumps-in-old-houses/)
- [Learn**How do Mass Save heat pump rebates work?** The three rebate tiers, the conditions behind each, the dates that change them, and what happens in towns with their own light plant.](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/)

## Get an estimate in Everett

Tell us what heats the house now and which rooms aren't working in Everett.

(857) 837-1475
