# Ducted heat pumps for Chelsea three-deckers, floor by floor

> Ducted heat pumps for Chelsea three-deckers and condos, one system per floor, with outdoor units fitted to tight lots and roofs on Eversource's winter rate.

URL: https://clementbostonheatpumps.com/service-areas/chelsea/

Service area, Massachusetts

Ducted heat pumps for Chelsea three-deckers and condos, one system per floor, with outdoor units fitted to tight lots and roofs on Eversource's winter rate.

(857) 837-1475

Last Updated: November 12, 2026

Electric

Eversource

Rebates

Mass Save

Permits

City of Chelsea building department

Energy code

Stretch energy code since July 1, 2017

## A typical Prattville top-floor heat pump

Horizontal air handler in the low attic of a three-decker

Outdoor unit on a stand on the rear porch roof

### Baseboard under the roof

The top-floor condo of a 1905 three-decker heats with electric baseboard in all five rooms and cools with window units. Winter bills are high and summers under the roof are hot. There is no yard at all, and the next house stands only a few feet away.

### Using the low attic

A 1.5-ton horizontal air handler fits in the low attic on vibration isolators once the hatch is enlarged to pass it. Short insulated branches drop to five ceiling registers, with a return in the hall. No unit hangs on any wall, and the floors below aren't touched.

### A spot off the ground

The only place the association allows is the flat roof over the rear porches. The unit sits on a rated, ballasted stand set back from the edge, after the framing is checked, with its 30-foot line set run down the rear wall in a cover. A night low-noise mode keeps it quiet toward the neighbors.

### Bills and paperwork

Each kilowatt-hour now moves two to three units of heat instead of one. Chelsea is on Eversource, so the system qualifies for Mass Save's rebate for replacing electric resistance heat, and the household's winter kilowatt-hours move to the seasonal heat pump rate. Permits go through the city.

*Project facts*

| Service | Electric baseboard to ducted heat pump |
| --- | --- |
| Where | Prattville, Chelsea |
| House | 1905 three-decker, top-floor condo, about 1,100 sq ft |
| Before | Electric baseboard and window AC |
| After | 1.5-ton attic heat pump, roof-mounted outdoor unit |
| Price | $22,600 before rebates |
| Time on site | Five working days |

## What brings people to us in Chelsea

### A top floor on electric baseboard

Three in ten Chelsea homes heat with electricity. An attic air handler gives the top floor heat and cooling at two to three times the output per kilowatt-hour.

### No yard at all

Outdoor units go on flat roofs, rear porch roofs or wall brackets, with line sets run up the back of the building.

### A shared gas boiler for three units

Splitting to one ducted system per floor gives each household its own controls and its own bill.

A Chelsea three-decker gives each floor about the same footprint and almost no yard to share. [Clement Boston Heat Pumps](https://clementbostonheatpumps.com/) handles heat pump installation in Chelsea, MA one floor at a time, fitting a ducted system and its outdoor unit into buildings where every square foot is spoken for.

Only about 8% of Chelsea’s homes are detached houses. The rest are two-families, three-deckers and larger buildings, and that shapes the whole job.

## Fitting a system into a Chelsea floor plate

Each floor of a three-decker is its own household and its own heat loss. We size a system per floor, then find a place for its air handler and a path for its ducts.

### Top floor

The top floor loses the most heat through the roof and gains the most sun in summer. Its air handler goes in the low attic, feeding short insulated branches to ceiling registers. See [attic air handlers](https://clementbostonheatpumps.com/attic-air-handler-heat-pump/).

### Middle floor

The middle floor is the hardest, with finished floors above and below. A compact unit in a closet or a small-duct system through the floor joists is the usual answer. Our [three-decker guide](https://clementbostonheatpumps.com/guide/triple-decker-heat-pumps/) shows the layouts.

### First floor

The basement takes the first floor’s air handler, with floor registers and a central return in the hall.

## Where outdoor units go when there’s no yard

Chelsea lots are narrow and often paved front to back. Outdoor units have to fit where they can be serviced, drain and stay quiet for the neighbors.

### Roofs and porch roofs

A flat rear roof or the roof over a back porch can carry a unit on a rated stand. We check the framing, keep the unit back from the edge and run the line set down the rear wall in a cover.

### Wall brackets

Where there’s no roof space, a bracket on the back wall holds the unit above snow and foot traffic. Bracket units need vibration isolation so the hum doesn’t carry into the rooms.

### Noise and neighbors

Chelsea’s local limits are confirmed per address. Statewide, MassDEP’s noise policy treats a source that raises the broadband level more than 10 dB(A) above the background as a violation, measured at the complaint location. On a lot where the next house is a few feet away, we pick low-sound equipment and set night modes.

## Electric heat, gas boilers and the Eversource rate

About 61% of Chelsea homes heat with gas and 30% with electricity, one of the highest electric shares near Boston. Oil is under 6%.

- **Electric baseboard and wall heaters:** each kilowatt-hour makes one unit of heat. A heat pump moves two to three on a typical winter day, so the savings show on the first bill. See [baseboard heat to heat pump](https://clementbostonheatpumps.com/baseboard-heat-to-heat-pump/).
- **Gas boilers:** gas costs less per BTU, so the case is closer. Owners switch for central cooling or when the boiler fails; see [boiler to heat pump conversion](https://clementbostonheatpumps.com/boiler-to-heat-pump-conversion/).

### The seasonal rate

Eversource’s seasonal heat pump rate lowers both distribution and transmission charges on every household kilowatt-hour from November 1 to April 30. Mass Save rebate recipients are usually enrolled automatically; see our [winter rate guide](https://clementbostonheatpumps.com/guide/heat-pump-electric-rate-massachusetts/).

### Panels in older buildings

Many Chelsea units have small panels, sometimes 60 or 100 amps. A load calculation shows whether a heat pump fits; if it doesn’t, the service upgrade comes first. See [panel upgrades for heat pumps](https://clementbostonheatpumps.com/electrical-panel-upgrade-for-heat-pump/).

## Switching one floor while the others stay put

In most Chelsea buildings, one owner moves first. The plan for that floor has to work today and leave room for the other floors later.

### Keeping the shared boiler running

Where one gas boiler heats all three floors, taking one floor off it means capping that floor’s loop at the boiler and rebalancing the rest. A licensed gas fitter handles any gas line work. The other two floors keep their heat without interruption.

### Reserving routes and roof space

The first system shouldn’t take the only chase or the whole roof. We run its line set and trunk so a second and third system can follow, and leave space on the roof or rear wall for their outdoor units.

### Sealing between units

Where a duct or line set passes from one floor to another, the opening is sealed with fire-rated material. That keeps the separation between households intact and stops smoke and sound from traveling up the building.

## Ducted or wall-mounted?

Wall-mounted ductless heads are the other option Chelsea owners weigh, but they put a unit in every room. We install ducted systems only, where one hidden air handler serves the whole floor.

A ducted system on a floor of five or six rooms gives even heat in every room, including bedrooms with the door closed, and nothing hangs on the walls. Our [ducted vs ductless guide](https://clementbostonheatpumps.com/guide/ducted-vs-ductless-heat-pump/) sets out the trade-offs.

## Chelsea permits, Eversource and the rebate path

Chelsea’s building department issues the permits; its online route is confirmed per address. A heat pump job needs an electrical permit and the city’s mechanical permits.

| What | The Chelsea figure |
| --- | --- |
| Electric utility | Eversource |
| Gas utility | National Grid (Boston Gas) |
| Energy code | Stretch code since July 1, 2017; specialized not adopted |
| Three- and four-unit buildings | 27.3% of homes |
| Heating fuel | Gas 60.8%, electricity 30.4%, oil 5.7% |

Chelsea is on the state’s coastal list, along Chelsea Creek and the Mystic. Roof units on the waterfront blocks get placement out of wind-driven spray; see our [placement guide](https://clementbostonheatpumps.com/guide/heat-pump-snow-stand/). For condos, our [condo guide](https://clementbostonheatpumps.com/guide/condo-heat-pump-replacement/) covers association approval.

## What happens, step by step, in Chelsea

The first visit looks at one floor or all three: a load per floor, the attic and basement, closets for a chase, the panel and the roof.

1. **Written estimate:** equipment and capacity at 5°F, duct routes, electrical, roof or bracket mounting, permits and the rebate path.
2. **Association sign-off** where the building is a condo.
3. **Install:** four to seven working days per floor, with the other floors living normally.
4. **Commissioning:** pressure test, vacuum below 500 microns, weighed charge, airflow and night sound settings.

[Everett](https://clementbostonheatpumps.com/service-areas/everett/) shares Chelsea’s two- and three-family stock across the Mystic, and [Revere](https://clementbostonheatpumps.com/service-areas/revere/) borders it to the north.

## Services in Chelsea

- [Service**Baseboard heat to heat pump** Replace electric baseboard with a ducted heat pump that heats on far less electricity and cools too.](https://clementbostonheatpumps.com/baseboard-heat-to-heat-pump/)
- [Service**Boiler to heat pump conversion** New ducts or small-duct high-velocity runs so a heat pump can heat and cool a radiator house.](https://clementbostonheatpumps.com/boiler-to-heat-pump-conversion/)
- [Service**Attic air handlers** An attic air handler that heats and cools the upper floor, with short sealed ducts and a guarded drain.](https://clementbostonheatpumps.com/attic-air-handler-heat-pump/)
- [Service**Heat pump ductwork** Duct testing, sealing, new returns and resized runs so a heat pump gets the air it needs.](https://clementbostonheatpumps.com/heat-pump-ductwork/)
- [Service**Panel and service upgrades** A service load calculation first, and a 200-amp upgrade only when the heat pump and the house need it.](https://clementbostonheatpumps.com/electrical-panel-upgrade-for-heat-pump/)

## How a job usually runs in Chelsea

### First call

You tell us what heats and cools the house now, which rooms aren't working, and roughly where the house is.

### Home visit

We measure the house for a load calculation, test the ducts, check the panel and look for an outdoor spot.

### Written estimate

Equipment, duct changes, electrical, permits and the rebate path, line by line, with our price.

### Install

Permits first, then the work: usually two to five working days on site.

### Commissioning

Pressure test, vacuum, charge by weight, airflow and controls set before we call it done.

## Neighborhoods, landmarks and routes

- Bellingham Square
- Chelsea Square
- Admiral's Hill
- Prattville
- Mill Hill
- Cary Square
- Box District
- Shurtleff-Bellingham

### Landmarks

- Tobin Bridge
- Chelsea Creek
- Mary O'Malley Park
- Chelsea City Hall
- Mystic River

### Getting around

- Route 1
- Broadway
- Route 16
- Everett Avenue

[Open Chelsea, MA in Google Maps](https://www.google.com/maps/search/?api=1&query=Chelsea%2C%20MA)

## Chelsea: questions

### What does a heat pump cost for one floor of a Chelsea three-decker?

A floor heated by baseboard or a boiler needs new ducts, where our typical range is $20,000 to $40,000 and up before rebates. Floor size, how far the ducts run and where the outdoor unit goes set the price on the written estimate.

### Can a heat pump outdoor unit go on a Chelsea roof?

Often, yes. A flat rear roof or a porch roof can hold the unit on a rated stand, once we check the structure and keep it back from the edge. A condo needs the association's approval, and the city's rules for your building are confirmed per address.

### Will my neighbors hear a heat pump on a tight Chelsea lot?

Chelsea's local noise rules are confirmed per address. Statewide, MassDEP treats a source that raises sound more than 10 dB(A) above the background level, or makes a pure tone, as a violation at the neighbor's home, so we pick quiet equipment and keep units away from bedroom windows.

### Is Chelsea on Eversource's heat pump rate?

Yes. Chelsea is Eversource electric territory, and Eversource's seasonal heat pump rate lowers both distribution and transmission charges on all your household kilowatt-hours from November 1 to April 30.

### Can the three units in a Chelsea building each get Mass Save rebates?

Mass Save's rebates are figured per system and per ton, so each floor's system is its own application. With Eversource for electricity and National Grid for gas, baseboard, oil and gas units all have a route.

## Nearby service areas

- [Service area**Everett** Ducted heat pumps for Everett two- and three-families moving off oil or gas boilers, with one system per unit and National Grid's winter heat pump rate.](https://clementbostonheatpumps.com/service-areas/everett/)
- [Service area**Revere** Ducted heat pumps for Revere homes from Beachmont to Point of Pines, mounted for salt air and flood zones, with National Grid rebates and CitizenServe permits.](https://clementbostonheatpumps.com/service-areas/revere/)
- [Service area**Winthrop** Ducted heat pumps for Winthrop homes, placed out of the salt wind and above flood levels, on National Grid with Mass Save rebates and the stretch code.](https://clementbostonheatpumps.com/service-areas/winthrop/)

## Guides for houses in Chelsea

- [Decision Guide**How do you put heat pumps in a triple-decker?** Three stacked homes under one roof, often with three owners, three meters and one narrow side yard. Here's how a heat pump job works around that.](https://clementbostonheatpumps.com/guide/triple-decker-heat-pumps/)
- [Decision Guide**What's involved in replacing a heat pump in a condo?** In a condo, the outdoor unit usually sits on common property, so the association, the master deed and sometimes a historic commission come before equipment.](https://clementbostonheatpumps.com/guide/condo-heat-pump-replacement/)
- [Learn**How does the heat pump electric rate work in Massachusetts?** Which part of your electric bill the seasonal rate lowers, why it applies to the whole house, how enrollment works, and what it means for the switch from oil or gas.](https://clementbostonheatpumps.com/guide/heat-pump-electric-rate-massachusetts/)
- [Decision Guide**Should I get a ducted or ductless heat pump?** Both are heat pumps. The difference is how the heat reaches each room, and that comes down to the ducts you have or could add.](https://clementbostonheatpumps.com/guide/ducted-vs-ductless-heat-pump/)
- [Learn**How high should a heat pump snow stand be, and where should the outdoor unit go?** The outdoor unit pulls heat from winter air, so snow, ice, salt and the neighbors all shape where it goes and what it sits on.](https://clementbostonheatpumps.com/guide/heat-pump-snow-stand/)

## Get an estimate in Chelsea

Tell us what heats the house now and which rooms aren't working in Chelsea.

(857) 837-1475
