# Ducted heat pumps for Canton, MA homes, before and after the code change

> Ducted heat pumps for Canton homes and condos on Eversource, planned around the specialized energy code that takes effect in town on January 1, 2027.

URL: https://clementbostonheatpumps.com/service-areas/canton/

Service area, Massachusetts

Ducted heat pumps for Canton homes and condos on Eversource, planned around the specialized energy code that takes effect in town on January 1, 2027.

(857) 837-1475

Last Updated: November 12, 2026

Electric

Eversource

Rebates

Mass Save

Permits

Canton Building Department (online permitting)

Energy code

Stretch energy code since July 1, 2017; specialized code effective January 1, 2027

## What a furnace-to-heat-pump job in Canton looks like

New return grille in the upstairs hall beside the linen closet

Air handler on the existing basement plenum where the gas furnace stood

### Two systems, both tired

A 1978 colonial near Canton Junction runs a 24-year-old gas furnace and a 22-year-old central AC through one set of basement ducts. Both still work, the upstairs bedrooms run warm every July, and the owners want one system for heating and cooling before either one fails.

### What the ducts allow

The load calculation comes to 34,800 BTU an hour at the design temperature, so a 3-ton cold-climate unit carries the house without the furnace. Static pressure reads 0.78 inch on the old system, because the upstairs has one small return. A new 20-by-10 return in the hall, run down a closet, brings it to about 0.48.

### The work

The furnace, coil and condenser come out and the refrigerant is recovered. The air handler sits on the existing plenum with a float switch and 5 kW of backup heat. A 40-amp circuit comes off the 200-amp panel, and the outdoor unit goes on an 18-inch stand behind the house.

### Closing it out

A licensed gas fitter caps the line. The 30-foot line set holds nitrogen pressure, pulls below 500 microns and is charged by weight. Airflow and static are measured at every register, the backup heat locks out above a set outdoor temperature, and the Mass Save paperwork goes through Eversource Gas.

*Project facts*

| Service | Gas furnace and AC to heat pump |
| --- | --- |
| Where | Canton Junction area, Canton |
| House | 1978 two-story colonial, about 2,200 sq ft |
| Before | 24-year-old gas furnace and 3-ton AC |
| After | 3-ton cold-climate heat pump on existing ducts |
| Price | $21,400 before rebates |
| Time on site | Four working days |

## What brings people to us in Canton

### An addition or gut renovation on the drawing board

Canton's specialized code takes effect January 1, 2027, so the permit date decides which code your new heating plan is checked against.

### A gas furnace and an old central AC

When both are near the end, one ducted heat pump replaces the pair on the ducts you already have, and the gas line is capped.

### A condo or townhouse on electric heat

Close to one Canton home in five heats with electricity, and a heat pump turns each kilowatt-hour into two to three units of heat.

### An oil furnace near the Blue Hills

Inland nights run colder than the harbor, so we size the system at the design temperature and check its output at 5°F.

Starting January 1, 2027, Canton’s new homes and major renovations come under the state’s specialized energy code. For an addition or gut renovation, your permit date decides which rules apply. [Clement Boston Heat Pumps](https://clementbostonheatpumps.com/) plans heat pump installation in Canton, MA for those projects and for the more common one: an existing house with an aging furnace.

For an existing house, the code change barely registers. What matters more is Eversource on the electric side, Eversource Gas on the gas side, and the ducts already in the basement or attic.

## Does the new code touch your project?

Only if you’re building new or doing a major renovation. A heating replacement in an existing Canton home is not that kind of project, so the new code won’t push your plan in either direction.

### Existing homes

Swapping a furnace, boiler or baseboard for a ducted heat pump is a mechanical replacement. The permit covers the electrical work and the ducts, and the energy code shows up mostly in duct sealing and insulation where ducts run through unheated space. Our [furnace conversion page](https://clementbostonheatpumps.com/furnace-to-heat-pump-conversion/) covers that job step by step, and [oil-to-heat-pump conversion](https://clementbostonheatpumps.com/oil-to-heat-pump-conversion/) covers the oil version.

### Additions and gut renovations

Canton has run the stretch code since 2017. From January 1, 2027, the specialized code applies, with all-electric or pre-wired paths for new construction and major renovations. A project permitted before that date follows the stretch code. We size the heat pump for the finished house, so the plan holds under either code.

### The rebate changes the same day

Mass Save’s whole-home rebate drops on January 1, 2027, from $2,650 a ton up to $8,500 to $2,350 a ton up to $7,500. On a three-ton system that’s $900. Our [rebate guide](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/) lists every condition.

## Canton houses, condos and where the ducts go

Most Canton homes are detached houses, but almost a third sit in buildings of five or more units. Only about one in nine predates 1940, so most houses were built with ducts or room for them.

### Colonials, capes and split-levels

A postwar house often has a furnace and ducts in the basement, sometimes with an AC air handler in the attic. Where both are aging, two right-sized heat pumps on the existing ducts replace all of it. We measure static pressure first, because undersized returns are the common reason a swap runs loud. See [whole-home heat pumps](https://clementbostonheatpumps.com/whole-home-heat-pump/).

### Where the air handler goes

In a basement, the air handler takes the furnace’s place on the existing plenum, with a condensate drain and a float switch. In an attic, it sits on a platform over a secondary pan, and flex duct in the cold space is replaced with sealed, insulated duct.

A split-level with ducts in a crawlspace gets the same leakage check before we reuse them.

### Condos and townhouses

In a complex, the association’s rules decide where the outdoor unit sits and what it looks like. We bring the spec, the sound rating and a placement sketch to the board early. Our [condo guide](https://clementbostonheatpumps.com/guide/condo-heat-pump-replacement/) walks through the approvals.

### Older houses near Canton Center

Where a house predates 1940 and heats with a boiler, there are no ducts to reuse. An attic air handler for the upper floor and a basement unit for the first, joined by a closet chase, is the common plan. Our [old-house guide](https://clementbostonheatpumps.com/guide/heat-pumps-in-old-houses/) covers the routing choices.

## Gas, electric and oil heat in Canton

About 60% of Canton homes heat with gas, 19% with electricity and 16% with oil. Each group starts the conversation from a different place.

| If you heat with | What usually drives the switch | The rebate side |
| --- | --- | --- |
| Gas furnace | Furnace and AC aging together; you want one system | Mass Save gas sponsor (Eversource Gas) |
| Electric baseboard | High winter bills in a condo or addition | Mass Save electric sponsor (Eversource) |
| Oil | Delivery costs and an old tank | Mass Save electric sponsor (Eversource) |

Gas is the cheapest fuel per unit of heat, so the running-cost case there is closer than for oil or baseboard. We show your actual numbers in the estimate; our [heat pump vs gas furnace guide](https://clementbostonheatpumps.com/guide/heat-pump-vs-gas-furnace-massachusetts/) explains the math. Baseboard homes see savings on the first bill; see [baseboard to heat pump](https://clementbostonheatpumps.com/baseboard-heat-to-heat-pump/).

## Sizing for a winter colder than the city’s

Canton sits inland, between the Blue Hills and Norwood, and its coldest nights run below Boston’s. That changes what the equipment has to deliver at the bottom of the scale.

### What the nearby weather station shows

Norwood Memorial Airport, next door, averages about five nights a year at or below 0°F, against fewer than one at Logan. It also sees around 18 nights at or below 10°F, nearly three times Logan’s count.

### How we size for it

We run a room-by-room load calculation at your town’s design temperature, then pick equipment by its rated capacity at 5°F, not its nameplate. Backup heat is sized for the rare night below that, and it locks out above a set temperature so it doesn’t run when the heat pump can carry the house. Our [sizing guide](https://clementbostonheatpumps.com/guide/heat-pump-sizing/) explains each step.

## Permits, Eversource and rebates in Canton

Canton’s building department takes permits online. A ducted job needs an electrical permit and a sheet metal permit, plus a gas permit when a licensed gas fitter caps a gas line.

| What | The Canton answer |
| --- | --- |
| Permit route | Canton Building Department, online permitting |
| Energy code | Stretch code since July 1, 2017; specialized code from January 1, 2027 |
| Electric utility | Eversource |
| Gas utility | Eversource Gas |
| Rebate program | Mass Save |
| Winter heat pump rate | Eversource, November 1 to April 30 |

Because Canton is Eversource territory, the [winter heat pump rate](https://clementbostonheatpumps.com/guide/heat-pump-electric-rate-massachusetts/) cuts both distribution and transmission charges on every household kilowatt-hour through the heating season. Rebate recipients are usually enrolled without a separate application.

Fees and local noise rules are confirmed per address when we apply. The [cost guide](https://clementbostonheatpumps.com/guide/heat-pump-installation-cost-massachusetts/) sets out our ranges.

## From the first visit to a working system

The first visit covers a room-by-room load calculation, a static pressure and leakage check on your ducts, the electrical panel and a spot for the outdoor unit.

- **Written estimate:** equipment with its capacity at 5°F, duct changes, electrical, permits, rebate path and price, line by line.
- **Timing:** if you’re near the January 1, 2027 rebate change, the estimate shows both figures.
- **Install:** usually three to six working days on existing ducts, longer where new ducts go in.
- **Commissioning:** nitrogen pressure test, vacuum below 500 microns, charge by weight, measured airflow and static, controls set and the backup heat lockout recorded.

Neighboring [Norwood](https://clementbostonheatpumps.com/service-areas/norwood/) runs its own light plant with a separate rebate, while [Milton](https://clementbostonheatpumps.com/service-areas/milton/) shares Canton’s Eversource service.

## Services in Canton

- [Service**Furnace to heat pump conversion** Take out the gas or propane furnace and heat and cool through the same ducts with a heat pump.](https://clementbostonheatpumps.com/furnace-to-heat-pump-conversion/)
- [Service**Whole-home heat pumps** One ducted system that heats and cools the whole house, with the furnace or boiler retired.](https://clementbostonheatpumps.com/whole-home-heat-pump/)
- [Service**Replace AC with a heat pump** When the central AC dies, a heat pump on the same ducts cools and adds a second source of heat.](https://clementbostonheatpumps.com/replace-ac-with-heat-pump/)
- [Service**Baseboard heat to heat pump** Replace electric baseboard with a ducted heat pump that heats on far less electricity and cools too.](https://clementbostonheatpumps.com/baseboard-heat-to-heat-pump/)
- [Service**Oil to heat pump conversion** Retire the oil furnace or hydro-air boiler, cap the oil line and heat and cool through the ducts you have.](https://clementbostonheatpumps.com/oil-to-heat-pump-conversion/)
- [Service**Heat pump ductwork** Duct testing, sealing, new returns and resized runs so a heat pump gets the air it needs.](https://clementbostonheatpumps.com/heat-pump-ductwork/)

## How a job usually runs in Canton

### First call

You tell us what heats and cools the house now, which rooms aren't working, and roughly where the house is.

### Home visit

We measure the house for a load calculation, test the ducts, check the panel and look for an outdoor spot.

### Written estimate

Equipment, duct changes, electrical, permits and the rebate path, line by line, with our price.

### Install

Permits first, then the work: usually two to five working days on site.

### Commissioning

Pressure test, vacuum, charge by weight, airflow and controls set before we call it done.

## Neighborhoods, landmarks and routes

- Canton Center
- Canton Junction
- Ponkapoag
- Springdale
- Canton Corner

### Landmarks

- Blue Hills Reservation
- Ponkapoag Pond
- Canton Viaduct
- Reservoir Pond
- Paul Revere Heritage Site

### Getting around

- Route 138
- Interstate 93
- Interstate 95
- Neponset Street

[Open Canton, MA in Google Maps](https://www.google.com/maps/search/?api=1&query=Canton%2C%20MA)

## Canton: questions

### Does Canton's specialized energy code apply if I'm only replacing my furnace?

No. The specialized code takes effect in Canton on January 1, 2027 and covers new homes and major renovations. Swapping a furnace for a heat pump in an existing house follows the code for that kind of work, which mostly shows up in duct sealing and insulation details.

### What does a ducted heat pump cost for a Canton house with a gas furnace?

Our typical range for a whole-home system on ducts we can reuse is $15,000 to $28,000 and up before rebates. Canton gas is Eversource Gas, a Mass Save sponsor, so the whole-home rebate can apply when the furnace comes out. Your written estimate sets the price.

### Will the Mass Save rebate be smaller if my Canton install slips into January?

Yes. The whole-home rebate is $2,650 a ton up to $8,500 for installs through 2026, and $2,350 a ton up to $7,500 from January 1, 2027. We put the timing on the estimate so you can see what a later start date costs.

### Which permits does a Canton heat pump job need?

An electrical permit and a sheet metal permit for duct work, plus a gas permit where a gas line is capped. Canton files building department permits online, and the fees are confirmed per address when we apply.

### Is there a winter electric rate for Canton homes with a heat pump?

Yes. Canton is Eversource territory, and Eversource's heat pump rate lowers distribution and transmission charges on all household kilowatt-hours from November 1 to April 30. Mass Save rebate recipients are usually enrolled automatically.

## Nearby service areas

- [Service area**Norwood** Ducted heat pumps for Norwood capes, two-families and condos, with Norwood Light or Mass Save rebates matched to your heating fuel and the specialized code.](https://clementbostonheatpumps.com/service-areas/norwood/)
- [Service area**Milton** Ducted heat pumps for Milton's detached houses with oil heat and two-zone ducts, on Eversource with Mass Save rebates and the winter heat pump rate.](https://clementbostonheatpumps.com/service-areas/milton/)
- [Service area**Randolph** Ducted heat pumps for Randolph capes, raised ranches and split-levels on oil, gas or baseboard, with Mass Save rebates and what the new stretch code changes.](https://clementbostonheatpumps.com/service-areas/randolph/)

## Guides for houses in Canton

- [Decision Guide**Should I replace my gas furnace with a heat pump in Massachusetts?** Gas is cheap heat per unit, so this comparison turns on cooling, rebates, the age of the furnace and town rules, not the fuel bill alone.](https://clementbostonheatpumps.com/guide/heat-pump-vs-gas-furnace-massachusetts/)
- [Learn**How do Mass Save heat pump rebates work?** The three rebate tiers, the conditions behind each, the dates that change them, and what happens in towns with their own light plant.](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/)
- [Learn**What size heat pump do I need?** Why square footage and the old unit's tonnage both mislead, what a room-by-room load calculation measures, and how the result turns into equipment.](https://clementbostonheatpumps.com/guide/heat-pump-sizing/)
- [Decision Guide**What's involved in replacing a heat pump in a condo?** In a condo, the outdoor unit usually sits on common property, so the association, the master deed and sometimes a historic commission come before equipment.](https://clementbostonheatpumps.com/guide/condo-heat-pump-replacement/)
- [Learn**How does the heat pump electric rate work in Massachusetts?** Which part of your electric bill the seasonal rate lowers, why it applies to the whole house, how enrollment works, and what it means for the switch from oil or gas.](https://clementbostonheatpumps.com/guide/heat-pump-electric-rate-massachusetts/)

## Get an estimate in Canton

Tell us what heats the house now and which rooms aren't working in Canton.

(857) 837-1475
