# Ducted heat pumps for Cambridge, MA houses and condos

> Ducted heat pumps for Cambridge houses and condos, planned around the fossil-fuel-free rule, HVAC noise limits and Mid-Cambridge and Old Cambridge review.

URL: https://clementbostonheatpumps.com/service-areas/cambridge/

Service area, Massachusetts

Ducted heat pumps for Cambridge houses and condos, planned around the fossil-fuel-free rule, HVAC noise limits and Mid-Cambridge and Old Cambridge review.

(857) 837-1475

Last Updated: November 12, 2026

Electric

Eversource

Rebates

Mass Save

Permits

Cambridge Inspectional Services Department

Energy code

Specialized stretch code since July 1, 2023

## What a boiler-to-heat-pump job in Mid-Cambridge looks like

New ceiling register in a finished third-floor bedroom

Outdoor units in the rear yard, out of the narrow side yard

### The house and the rule

An 1890s three-story house on a narrow lot, heated by a gas steam boiler, with the third floor and kitchen being gutted. Because it's a major renovation, Cambridge's fossil-fuel-free ordinance rules out a new gas boiler or furnace, so the heat has to be electric.

### Using the renovation

With the third floor open, a 2-ton attic air handler feeds the top two floors through the new framing and two closets that stack between floors 2 and 3. A 1.5-ton basement unit reaches the first floor through floor registers, so the finished plaster downstairs stays closed.

### Where the outdoor units go

The 9-foot side yard sits against the neighbor's bedroom windows, and Cambridge's guidance holds HVAC equipment to 50 dB(A) at night at the lot line. So both units go to the rear yard on a sound-rated stand, set to low-noise mode at night, with a sound reading at the line before we finish. Mid-Cambridge is a neighborhood conservation district, and a rear-yard unit not visible from the street is the kind of work the Historical Commission usually clears with a Certificate of Non-Applicability.

### Sequence and permits

Ducts are roughed in before the drywall, the boiler comes out once the heat pumps carry the house, and permits go through Cambridge Inspectional Services. Twelve supply registers, two returns, line sets of 38 and 22 feet, all pressure-tested, evacuated and charged by weight.

*Project facts*

| Service | Boiler-to-heat-pump conversion with new ducts |
| --- | --- |
| Where | Mid-Cambridge |
| House | 1890s three-story single-family, about 2,600 sq ft |
| Before | Gas steam boiler and radiators, window AC |
| After | 2-ton attic and 1.5-ton basement heat pumps |
| Price | $36,800 before rebates |
| Time on site | Nine working days, timed around a renovation |

## What brings people to us in Cambridge

### A renovation that can't put gas back

Cambridge's fossil-fuel-free ordinance keeps new gas or oil equipment out of the work area of a major renovation, so the new heat is electric.

### A three-decker or condo with window units

Each unit gets its own system sized for its own floor, with the board or the other owners signing off on where the outdoor units go.

### A narrow side yard

The city holds HVAC equipment to 50 dB(A) at night at the neighbor's line, which usually moves the outdoor unit to the rear or the roof.

### A steam or hot-water house with no ducts

Attic and basement air handlers, stacked closets or small-duct systems bring ducted heat and cooling without opening every wall.

Close to half of Cambridge’s homes were built before 1940, most for steam or hot-water radiators. [Clement Boston Heat Pumps](https://clementbostonheatpumps.com/) installs ducted heat pumps in Cambridge houses, two-families and condos, planned around three rules that make a Cambridge job different.

Those rules are the fossil-fuel-free ordinance, the city’s HVAC noise limits and historic review where it applies. Each one changes the plan before we choose any equipment.

## Why Cambridge jobs start with the rules

Three Cambridge rules shape where the heat comes from, where the outdoor unit sits and who signs off. We check all three on the first visit.

### Fossil-fuel-free renovations

Since March 22, 2024, Cambridge’s ordinance has kept new fossil-fuel equipment out of new buildings and out of the work area of major renovations. If you’re gutting a floor and replacing the heat at the same time, the new heat is electric.

A gas furnace kept as backup isn’t available for that work, so the ducted heat pump is the main system. We size it to carry the coldest night without leaning on backup strips; see [whole-home heat pumps](https://clementbostonheatpumps.com/whole-home-heat-pump/).

### Noise at the lot line

The city’s HVAC noise handout sets 50 dB(A) from 6 p.m. to 7 a.m. and 60 dB(A) by day, measured from your neighbor’s property line. The handout itself warns that many units turn out to be in violation once running.

On lots where side yards are a few feet wide, that limit decides where the unit goes. We check the unit’s rated sound against the distance to the line, favor rear yards and roofs, and take a reading at the line before we finish. Our [outdoor unit placement guide](https://clementbostonheatpumps.com/guide/heat-pump-snow-stand/) covers the rest.

### Historic and conservation districts

Old Cambridge and Fort Washington are historic districts. Avon Hill, Half Crown-Marsh, Harvard Square and Mid-Cambridge are neighborhood conservation districts, where exterior work visible from a public way can need Cambridge Historical Commission review.

A unit in a rear yard or on a roof the street can’t see usually qualifies for a Certificate of Non-Applicability, often issued on the spot. We photograph the spot from the street on the first visit so the question is answered early.

## The houses we see, and where the ducts go

Cambridge is mostly multi-family. More than half its homes sit in buildings of five or more units, and only about one in ten is a detached house. That shapes the job more than the equipment does.

### Three-deckers and two-families

Each unit gets its own system sized for its own floor, because the top floor loses far more heat through the roof than the one below. The top unit’s air handler goes in the attic, the first floor’s in the basement, the middle one in a closet or on a small-duct system. Our [three-decker guide](https://clementbostonheatpumps.com/guide/triple-decker-heat-pumps/) walks through it.

### Condos

The board and the master deed decide where outdoor units can sit. We bring the spec, the sound rating and a placement drawing to that conversation early; see [condo heat pump replacement](https://clementbostonheatpumps.com/guide/condo-heat-pump-replacement/).

### Single-family houses with radiators

In a Victorian or a Cambridgeport single-family, the usual plan is an [attic air handler](https://clementbostonheatpumps.com/attic-air-handler-heat-pump/) for the upper floors and a basement unit for the first, with stacked closets carrying the trunk. Renovations make it easier, because the ducts go in before the drywall. See [boiler and radiator homes](https://clementbostonheatpumps.com/boiler-to-heat-pump-conversion/).

## Electric heat, gas heat and what changes the savings

About 28% of Cambridge homes already heat with electricity, against roughly 64% on gas and under 4% on oil. Which group you’re in changes the case for a heat pump more than anything else.

### If your condo heats with baseboard

In an older condo, electric heat usually means baseboard or wall heaters, which turn one kilowatt-hour into one unit of heat. A heat pump moves two to three units for the same kilowatt-hour on a typical winter day.

The savings show up on the first bill, and Mass Save counts electric resistance heat as an eligible system to replace. See [electric baseboard to heat pump](https://clementbostonheatpumps.com/baseboard-heat-to-heat-pump/).

### If you heat with gas

Gas is the cheapest fuel per BTU, so the running-cost case is closer. Most Cambridge owners on gas switch because the boiler is near the end, they want central cooling, or a renovation rules out new gas equipment. We put the running cost on your actual rates in the estimate; see [heat pump vs gas furnace](https://clementbostonheatpumps.com/guide/heat-pump-vs-gas-furnace-massachusetts/).

## Code and rebate rules that apply in Cambridge

Cambridge’s Inspectional Services Department issues the electrical permit and a separate sheet metal permit, plus a building permit when the work is part of a renovation.

| What | The Cambridge figure |
| --- | --- |
| Sheet metal permit fee | $50 plus $25 per 100 linear feet of duct |
| Work started before a permit | Triple fees |
| Heat pump sheet metal permits, Nov 2021 to Oct 2026 | 294, about three in four for ducted systems |
| Energy code | Specialized stretch code since July 1, 2023 |
| Electric utility | Eversource |

Cambridge homes are on Eversource, so Mass Save’s rebates apply, along with the [winter heat pump rate](https://clementbostonheatpumps.com/guide/heat-pump-electric-rate-massachusetts/). Most Cambridge homes heat with gas, and Mass Save’s whole-home rebate covers replacing gas heat when the old system comes out.

That rebate also needs cold-climate equipment and an installer in Mass Save’s network; our [rebate guide](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/) lists the conditions. The [cost guide](https://clementbostonheatpumps.com/guide/heat-pump-installation-cost-massachusetts/) sets out our ranges.

## From first call to commissioning in Cambridge

The first visit covers the load calculation, the ducts or routes for new ones, the panel and the outdoor spot, measured against every lot line. In a district, we photograph the spot from the street.

- **Written estimate:** equipment, duct work, electrical, permits and the rebate path, line by line.
- **Renovation timing:** we work to the general contractor’s framing and drywall schedule, so ducts are roughed in while the walls are open.
- **Permits first,** then the install, usually two to nine working days depending on new ducts.
- **Commissioning:** pressure test, vacuum, charge by weight, airflow, controls, and a sound reading at the lot line.

Neighboring [Somerville](https://clementbostonheatpumps.com/service-areas/somerville/) runs its own permit office and allows dual fuel; [Arlington](https://clementbostonheatpumps.com/service-areas/arlington/) shares Cambridge’s fossil-fuel-free approach.

## Services in Cambridge

- [Service**Boiler to heat pump conversion** New ducts or small-duct high-velocity runs so a heat pump can heat and cool a radiator house.](https://clementbostonheatpumps.com/boiler-to-heat-pump-conversion/)
- [Service**Whole-home heat pumps** One ducted system that heats and cools the whole house, with the furnace or boiler retired.](https://clementbostonheatpumps.com/whole-home-heat-pump/)
- [Service**Attic air handlers** An attic air handler that heats and cools the upper floor, with short sealed ducts and a guarded drain.](https://clementbostonheatpumps.com/attic-air-handler-heat-pump/)
- [Service**Furnace to heat pump conversion** Take out the gas or propane furnace and heat and cool through the same ducts with a heat pump.](https://clementbostonheatpumps.com/furnace-to-heat-pump-conversion/)
- [Service**Heat pump ductwork** Duct testing, sealing, new returns and resized runs so a heat pump gets the air it needs.](https://clementbostonheatpumps.com/heat-pump-ductwork/)
- [Service**Replace AC with a heat pump** When the central AC dies, a heat pump on the same ducts cools and adds a second source of heat.](https://clementbostonheatpumps.com/replace-ac-with-heat-pump/)

## How a job usually runs in Cambridge

### First call

You tell us what heats and cools the house now, which rooms aren't working, and roughly where the house is.

### Home visit

We measure the house for a load calculation, test the ducts, check the panel and look for an outdoor spot.

### Written estimate

Equipment, duct changes, electrical, permits and the rebate path, line by line, with our price.

### Install

Permits first, then the work: usually two to five working days on site.

### Commissioning

Pressure test, vacuum, charge by weight, airflow and controls set before we call it done.

## Neighborhoods, landmarks and routes

- Mid-Cambridge
- Cambridgeport
- Riverside
- Agassiz
- Neighborhood Nine
- North Cambridge
- East Cambridge
- The Port
- Wellington-Harrington
- Strawberry Hill

### Landmarks

- Harvard Square
- Central Square
- Inman Square
- Porter Square
- Fresh Pond

### Getting around

- Massachusetts Avenue
- Cambridge Street
- Memorial Drive
- Route 2 at Alewife

[Open Cambridge, MA in Google Maps](https://www.google.com/maps/search/?api=1&query=Cambridge%2C%20MA)

## Cambridge: questions

### Can I replace my gas boiler with a new gas boiler during a Cambridge renovation?

Not inside the work area of a major renovation. Cambridge's fossil-fuel-free ordinance, in effect since March 22, 2024, keeps new fossil-fuel equipment out of new buildings and major renovations. A like-for-like boiler swap outside a major renovation is a different case; we check which one your project is.

### How loud can my outdoor unit be in Cambridge?

The city's HVAC noise handout sets 50 dB(A) from 6 p.m. to 7 a.m. and 60 dB(A) during the day, measured from your neighbor's property line. We place and select the unit to meet that, and take a reading at the line before we finish.

### Do I need Historical Commission approval for a heat pump in Mid-Cambridge?

Mid-Cambridge is a neighborhood conservation district, so exterior work visible from a public way can need review. An outdoor unit in a rear yard that the street can't see usually gets a Certificate of Non-Applicability, which the Commission often issues on the spot.

### What does a ducted heat pump cost in a Cambridge house?

Our typical range for a whole-home system on ducts we can reuse is $15,000 to $28,000 and up before rebates. Most Cambridge houses heat with radiators and need new ducts, where our typical range is $20,000 to $40,000 and up. Your written estimate sets the price.

### Which permits does a Cambridge heat pump job need?

Usually an electrical permit and a sheet metal permit from Inspectional Services, plus a building permit when the work is part of a renovation. Cambridge's sheet metal fee is $50 plus $25 per 100 linear feet of duct, and work started before a permit is issued pays triple fees.

## Nearby service areas

- [Service area**Somerville** Ducted heat pumps for Somerville two-families, three-deckers and condos, planned floor by floor, with sheet metal permits and gas backup still allowed.](https://clementbostonheatpumps.com/service-areas/somerville/)
- [Service area**Arlington** Ducted heat pumps for Arlington renovations under the fossil-fuel-free by-law and the specialized code, in bungalows, two-families and Heights colonials.](https://clementbostonheatpumps.com/service-areas/arlington/)
- [Service area**Newton** Ducted heat pumps for Newton colonials, Victorians and two-families, planned around the city's fossil-fuel-free ordinance and the specialized energy code.](https://clementbostonheatpumps.com/service-areas/newton/)

## Guides for houses in Cambridge

- [Decision Guide**How do you put heat pumps in a triple-decker?** Three stacked homes under one roof, often with three owners, three meters and one narrow side yard. Here's how a heat pump job works around that.](https://clementbostonheatpumps.com/guide/triple-decker-heat-pumps/)
- [Decision Guide**What's involved in replacing a heat pump in a condo?** In a condo, the outdoor unit usually sits on common property, so the association, the master deed and sometimes a historic commission come before equipment.](https://clementbostonheatpumps.com/guide/condo-heat-pump-replacement/)
- [Decision Guide**Will a heat pump work in an old house?** Boston has one of the oldest housing stocks in the country. Age changes how a heat pump goes in, not whether it can heat the house.](https://clementbostonheatpumps.com/guide/heat-pumps-in-old-houses/)
- [Cost Guide**How much does heat pump installation cost in Massachusetts?** Our typical ranges for Boston-area ducted heat pump jobs, what's inside the price, and what rebates do to it.](https://clementbostonheatpumps.com/guide/heat-pump-installation-cost-massachusetts/)
- [Learn**How do Mass Save heat pump rebates work?** The three rebate tiers, the conditions behind each, the dates that change them, and what happens in towns with their own light plant.](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/)

## Get an estimate in Cambridge

Tell us what heats the house now and which rooms aren't working in Cambridge.

(857) 837-1475
