# Ducted heat pumps for Burlington's postwar houses

> Ducted heat pumps for Burlington's postwar ranches and colonials, reusing furnace and AC ducts, with Mass Save rebates and Eversource's winter heat pump rate.

URL: https://clementbostonheatpumps.com/service-areas/burlington/

Service area, Massachusetts

Ducted heat pumps for Burlington's postwar ranches and colonials, reusing furnace and AC ducts, with Mass Save rebates and Eversource's winter heat pump rate.

(857) 837-1475

Last Updated: November 12, 2026

Electric

Eversource

Rebates

Mass Save

Permits

Town of Burlington building department (OpenGov permit portal)

Energy code

Stretch energy code since July 1, 2019

## What an oil-to-heat-pump job in Fox Hill looks like

Oil furnace with its AC coil in a Burlington ranch basement

Heat pump outdoor unit raised on a stand on the old condenser pad

### The prompt

In a 1958 Fox Hill ranch, the central air condenser is failing and the oil furnace beside it still burns through deliveries every winter. Replacing just the AC is on the table, but the owners want oil gone, and Mass Save's whole-home rebate, through Eversource, rewards taking the furnace out.

### Short ducts, one fix

A ranch's basement trunk is short, and the nine floor registers measure well. The single hall return is the limit: at heat pump airflow it pushes static pressure too high. Enlarging the grille to 20x30 with a 4-inch filter rack solves it without touching the trunk.

### The install

A 3-ton cold-climate outdoor unit goes on the old condenser pad, raised on a stand, and reuses the wall penetration. The variable-speed air handler takes the furnace's spot. Sizing at Burlington's design temperature matters here: nearby Hanscom Field averages about five nights a year at or below 0°F.

### Timing the rebate

The job is scheduled to be installed before January 1, 2027, when the whole-home rebate drops from $2,650 to $2,350 a ton. After commissioning, the furnace and tank come out, which the whole-home tier requires, and the rebate usually enrolls the house in Eversource's winter heat pump rate.

*Project facts*

| Service | Oil furnace and AC to a whole-home heat pump |
| --- | --- |
| Where | Fox Hill, Burlington |
| House | 1958 ranch, about 1,500 sq ft |
| Before | Oil furnace, failing central AC |
| After | 3-ton cold-climate system on existing ducts |
| Price | $19,700 before rebates |
| Time on site | Three working days |

## What brings people to us in Burlington

### An oil furnace with central air

The ducts already reach every room. Once static pressure and the return check out, a heat pump air handler takes the furnace's place.

### A central air system near the end of its life

Replacing the outdoor AC with a heat pump adds heating to the same ducts for a modest step up in cost.

### A townhouse or condo near Route 128

The association sets where outdoor units go. We bring the spec, sound rating and a placement sketch to that conversation.

A Burlington ranch or split-level with central air already has most of what a ducted heat pump needs: ducts that reach every room and a pad outside for the condenser. [Clement Boston Heat Pumps](https://clementbostonheatpumps.com/) builds each heat pump installation in Burlington, MA on that head start, then checks whether the ducts can carry winter air.

That makes many jobs here shorter than in older towns. About 94% of Burlington’s homes were built after 1939, mostly with forced air.

## Ducts that are already there

A furnace and central air leave a duct system the heat pump can reuse. The question is whether ducts sized for summer cooling and a furnace’s hot air move enough air for a heat pump in January.

### What we measure

We read total static pressure with the blower running, size the return against the airflow the new system needs, and look for leaks at the plenum and joints in the basement or attic. A heat pump moves more air at a lower temperature than a furnace, so a tight return is the most common fix.

### Fixes that keep it a short job

A second return grille, a larger filter rack or a sealed plenum often solves it without opening ceilings. When a branch is undersized, we replace just that run; see [heat pump ductwork](https://clementbostonheatpumps.com/heat-pump-ductwork/).

### Replacing only the air conditioning

If the AC is the part that’s worn out, a heat pump can replace it and share the work with the furnace. Our [heat pump vs central AC guide](https://clementbostonheatpumps.com/guide/heat-pump-vs-central-ac/) compares the two, and [replacing AC with a heat pump](https://clementbostonheatpumps.com/replace-ac-with-heat-pump/) explains the job.

## When the house has a boiler and no ducts

Not every Burlington house came with forced air. Some ranches and colonials heat with an oil or gas boiler and baseboard, with window units or nothing for cooling.

### Ranches

A one-story ranch is the easiest boiler house to convert. The air handler goes in the attic or the basement, and short branches drop to ceiling or floor registers in every room. Our [attic air handler](https://clementbostonheatpumps.com/attic-air-handler-heat-pump/) page explains the attic option.

### Colonials and split-levels

Two-story houses usually split into two systems: one in the attic for the bedrooms and one in the basement for the main floor. Where a closet stacks between floors, one system can sometimes serve both. See [boiler to heat pump conversion](https://clementbostonheatpumps.com/boiler-to-heat-pump-conversion/).

## Condos and townhouses

About 22% of Burlington homes sit in buildings of five or more units, many of them complexes near Route 128 and Route 3. The equipment choice there follows the association’s rules as much as the load.

### What the association decides

The master deed sets where outdoor units can sit, how line sets cross shared walls and who maintains them afterward. A compact air handler in a closet usually replaces the old furnace or AC unit in place; see [condo heat pump replacement](https://clementbostonheatpumps.com/guide/condo-heat-pump-replacement/).

## Oil, gas and the Eversource winter rate

About 52% of Burlington homes heat with gas and 32% with oil, well above the state’s 22% oil share. Both groups qualify for Mass Save, through Eversource on the electric side or National Grid on the gas side.

- **Oil homes** drop the costliest common fuel. The tank comes out under the fire department’s permit; see [oil to heat pump conversion](https://clementbostonheatpumps.com/oil-to-heat-pump-conversion/).
- **Gas homes** switch for cooling, a tired furnace or one system year-round; see [furnace to heat pump conversion](https://clementbostonheatpumps.com/furnace-to-heat-pump-conversion/).
- **Electric heat homes,** about 12%, swap baseboard that gives one unit of heat per kilowatt-hour for equipment that gives two to three.

### The winter rate

Eversource’s heat pump rate lowers distribution and transmission charges on every kilowatt-hour from November 1 to April 30. Mass Save rebate recipients are usually enrolled automatically; see the [electric rate guide](https://clementbostonheatpumps.com/guide/heat-pump-electric-rate-massachusetts/).

## Mass Save timing: this year or next

The whole-home rebate steps down on January 1, 2027, from $2,650 a ton up to $8,500 to $2,350 a ton up to $7,500. For a three-ton house, that is $900 less.

### What the rebate needs

Cold-climate listed equipment, an installer in Mass Save’s network, the old system removed or disconnected, and proof of weatherization. We install qualifying equipment as a participating contractor; the [rebate guide](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/) covers the details.

### Paying over time

Mass Save’s HEAT Loan offers 0% financing up to $25,000 through participating lenders, and you apply before work begins. The [HEAT Loan guide](https://clementbostonheatpumps.com/guide/mass-save-heat-loan-heat-pump/) explains the steps.

## Sizing for Hanscom’s cold nights

Burlington borders Bedford, where Hanscom Field averages about 5.3 nights a year at or below 0°F against 0.6 at Logan. Those nights set the size of the system, and they come more often here than closer to the harbor.

We calculate the load room by room at Burlington’s design temperature and choose equipment by its capacity at 5°F. Sizing to the full heating need also earns Mass Save’s $500 sizing bonus; our [sizing guide](https://clementbostonheatpumps.com/guide/heat-pump-sizing/) explains the method.

## Rebates, rates and permits for Burlington houses

Burlington takes permit applications through its OpenGov portal. The exact set is confirmed per address, usually electrical plus the mechanical permit for equipment and ducts.

| What | The Burlington figure |
| --- | --- |
| Electric utility | Eversource |
| Gas utility | National Grid |
| Mass Save whole-home rebate | $2,650 a ton up to $8,500 through 2026; $2,350 a ton up to $7,500 from January 1, 2027 |
| Energy code | Stretch code since July 1, 2019 |
| Built after 1939 | About 94% of homes |
| Heating fuel | Gas 52.1%, oil 31.8%, electricity 11.8% |

Where new ducts are needed, our typical range is $20,000 to $40,000 and up before rebates. The [cost guide](https://clementbostonheatpumps.com/guide/heat-pump-installation-cost-massachusetts/) lists our other ranges and what moves them.

## What to expect on a Burlington job

With ducts in place, most Burlington installs run two to four working days. The first visit decides whether that holds.

1. **Visit:** load calculation, static pressure and return check, panel, and the old condenser pad.
2. **Estimate:** equipment with 5°F capacity, duct fixes, electrical, permits, rebate tier and price.
3. **Install:** air handler swap, outdoor unit, line set, and the furnace and tank removed if planned.
4. **Commissioning:** nitrogen pressure test, vacuum below 500 microns, charge by weight, airflow and backup lockout set.

[Woburn](https://clementbostonheatpumps.com/service-areas/woburn/), [Bedford](https://clementbostonheatpumps.com/service-areas/bedford/) and [Lexington](https://clementbostonheatpumps.com/service-areas/lexington/) border Burlington, each with its own permit office.

## Services in Burlington

- [Service**Whole-home heat pumps** One ducted system that heats and cools the whole house, with the furnace or boiler retired.](https://clementbostonheatpumps.com/whole-home-heat-pump/)
- [Service**Oil to heat pump conversion** Retire the oil furnace or hydro-air boiler, cap the oil line and heat and cool through the ducts you have.](https://clementbostonheatpumps.com/oil-to-heat-pump-conversion/)
- [Service**Replace AC with a heat pump** When the central AC dies, a heat pump on the same ducts cools and adds a second source of heat.](https://clementbostonheatpumps.com/replace-ac-with-heat-pump/)
- [Service**Furnace to heat pump conversion** Take out the gas or propane furnace and heat and cool through the same ducts with a heat pump.](https://clementbostonheatpumps.com/furnace-to-heat-pump-conversion/)
- [Service**Oil tank removal** The old basement tank pumped, cleaned, removed and permitted once the heat pump is running.](https://clementbostonheatpumps.com/oil-tank-removal/)
- [Service**Air handler replacement** A new indoor unit matched to the outdoor heat pump you already have.](https://clementbostonheatpumps.com/heat-pump-air-handler-replacement/)

## How a job usually runs in Burlington

### First call

You tell us what heats and cools the house now, which rooms aren't working, and roughly where the house is.

### Home visit

We measure the house for a load calculation, test the ducts, check the panel and look for an outdoor spot.

### Written estimate

Equipment, duct changes, electrical, permits and the rebate path, line by line, with our price.

### Install

Permits first, then the work: usually two to five working days on site.

### Commissioning

Pressure test, vacuum, charge by weight, airflow and controls set before we call it done.

## Neighborhoods, landmarks and routes

- Burlington Center
- Fox Hill
- Pine Glen
- Francis Wyman
- Memorial

### Landmarks

- Mill Pond Reservoir
- Simonds Park
- Burlington Mall
- Landlocked Forest
- Vine Brook

### Getting around

- Interstate 95 (Route 128)
- Route 3
- Route 3A (Cambridge Street)
- Route 62

[Open Burlington, MA in Google Maps](https://www.google.com/maps/search/?api=1&query=Burlington%2C%20MA)

## Burlington: questions

### What does it cost to put a heat pump on my Burlington furnace ducts?

On ducts we can reuse, our typical range for a whole-home heat pump is $15,000 to $28,000 and up before rebates. Burlington is on Eversource, so Mass Save's whole-home rebate applies when the old system comes out. Your written estimate after the home visit sets the price.

### Will the Mass Save heat pump rebate drop next year?

Yes. Whole-home installs through 2026 get $2,650 a ton up to $8,500. From January 1, 2027, it is $2,350 a ton up to $7,500. If you're close to deciding, the install date matters more than the contract date.

### Can I replace just my Burlington central air with a heat pump?

Yes. A heat pump in place of the outdoor AC heats and cools through the same ducts, with the furnace kept as backup or removed. Keeping the furnace with integrated controls fits Mass Save's partial-home tier rather than whole-home.

### Does Eversource have a cheaper winter rate for Burlington heat pump homes?

Eversource's heat pump rate lowers distribution and transmission charges on all household kilowatt-hours from November 1 to April 30. Homes that received a Mass Save heat pump rebate are usually enrolled automatically.

### How do I apply for a heat pump permit in Burlington?

Burlington takes permit applications through its OpenGov online portal, linked from the town website. The exact set, usually electrical plus the mechanical permit for equipment and ducts, is confirmed per address, and we file them before work starts.

## Nearby service areas

- [Service area**Woburn** Ducted heat pumps for Woburn homes moving off oil, sized for colder inland nights, with Eversource's winter rate, Mass Save rebates and CitizenServe permits.](https://clementbostonheatpumps.com/service-areas/woburn/)
- [Service area**Bedford** Ducted heat pumps for Bedford homes, sized for Hanscom Field's colder nights, with Mass Save rebates through Eversource and dual fuel still allowed here.](https://clementbostonheatpumps.com/service-areas/bedford/)
- [Service area**Lexington** Cold-climate ducted heat pumps for Lexington homes on oil, propane or gas, sized for Hanscom-area winters and planned around the town's fossil-fuel-free bylaw.](https://clementbostonheatpumps.com/service-areas/lexington/)

## Guides for houses in Burlington

- [Decision Guide**Should I replace my central AC with a heat pump?** A heat pump is an air conditioner that also runs in reverse. When the AC fails, the choice is whether to buy cooling alone or cooling plus heat.](https://clementbostonheatpumps.com/guide/heat-pump-vs-central-ac/)
- [Learn**How do Mass Save heat pump rebates work?** The three rebate tiers, the conditions behind each, the dates that change them, and what happens in towns with their own light plant.](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/)
- [Learn**How does the heat pump electric rate work in Massachusetts?** Which part of your electric bill the seasonal rate lowers, why it applies to the whole house, how enrollment works, and what it means for the switch from oil or gas.](https://clementbostonheatpumps.com/guide/heat-pump-electric-rate-massachusetts/)
- [Learn**How does the Mass Save HEAT Loan work for a heat pump?** A 0% loan through participating banks and credit unions, the steps that have to happen before the work starts, and where it stops covering a job.](https://clementbostonheatpumps.com/guide/mass-save-heat-loan-heat-pump/)
- [Learn**What size heat pump do I need?** Why square footage and the old unit's tonnage both mislead, what a room-by-room load calculation measures, and how the result turns into equipment.](https://clementbostonheatpumps.com/guide/heat-pump-sizing/)

## Get an estimate in Burlington

Tell us what heats the house now and which rooms aren't working in Burlington.

(857) 837-1475
