# Bedford, MA heat pumps sized for Hanscom's cold nights

> Ducted heat pumps for Bedford homes, sized for Hanscom Field's colder nights, with Mass Save rebates through Eversource and dual fuel still allowed here.

URL: https://clementbostonheatpumps.com/service-areas/bedford/

Service area, Massachusetts

Ducted heat pumps for Bedford homes, sized for Hanscom Field's colder nights, with Mass Save rebates through Eversource and dual fuel still allowed here.

(857) 837-1475

Last Updated: November 12, 2026

Electric

Eversource

Rebates

Mass Save

Permits

Town of Bedford building department

Energy code

Specialized stretch code since July 1, 2024

## A typical Bedford Center furnace-to-heat-pump conversion

New return grille in the lower-level family room

Outdoor unit on a tall stand along the east wall

### The house

A 1972 split-level near Bedford Center, about 1,900 square feet, with a 24-year-old gas furnace on the lower level and a central air condenser that has stopped cooling. Both half-levels share one perimeter trunk, and the lower-level family room, half below grade, runs cold every January.

### Furnace kept or furnace out

Bedford still allows dual fuel, so keeping the furnace is on the table. At 24 years old it is a poor thing to build around, and Mass Save's whole-home tier pays more than the partial tier. The furnace comes out, and a licensed gas fitter caps the line.

### Sizing for Hanscom nights

The Manual J load is 32,800 BTU/h at the design temperature for the address. A 3-ton variable-speed unit delivers about 33,500 at 5°F, so its 5 kW strip covers defrost and the rare night colder than that. The lockout is set at 5°F and written on the air handler.

### Ducts, price and time

Static pressure passes once a 12 by 8 inch return goes into the family room. The outdoor unit sits on a 24-inch stand on the east side, clear of the drifts along the north wall. The job is $21,300 before rebates and takes three working days.

*Project facts*

| Service | Gas furnace to heat pump conversion |
| --- | --- |
| Where | Near Bedford Center |
| House | 1972 split-level, about 1,900 sq ft |
| Before | 24-year-old gas furnace, failed central air |
| After | 3-ton cold-climate heat pump on the existing ducts |
| Price | $21,300 before rebates |
| Time on site | Three working days |

## What brings people to us in Bedford

### A furnace and central air near the end

One cold-climate heat pump on the existing ducts replaces both, sized for nights at Hanscom that run colder than the city's.

### A young gas furnace worth keeping

Bedford still allows a heat pump paired with a gas furnace, and Mass Save's partial-home rebate covers that design with integrated controls.

### A townhouse or condo on electric heat

About 13% of Bedford homes heat with electricity. A small ducted air handler moves two to three units of heat for each unit a baseboard makes.

### Hot-water baseboard and no ducts

A basement air handler for the first floor and an attic unit for the bedrooms bring ducted heat and cooling to a boiler house.

On an average winter, Hanscom Field in Bedford drops to 0°F or below on about five nights, while Logan Airport manages it less than once. Those nights decide the size and the backup plan for heat pump installation in Bedford, MA, so they’re the first thing [Clement Boston Heat Pumps](https://clementbostonheatpumps.com/) checks.

Bedford is on Eversource, so Mass Save’s rebates and the winter heat pump rate apply. It’s also a comparison town in the state’s fossil-fuel-free program, which keeps dual fuel available where Concord and Lexington have ruled it out.

## Sizing for Hanscom’s winter, not the harbor’s

Hanscom’s weather station logs about 19 nights a year at 10°F or below and about 5,996 heating degree days, against roughly 7 nights and 5,545 degree days at Logan. More cold hours mean more heat to supply, and less margin at the bottom.

### Capacity where it counts

We size from a room-by-room Manual J at the design temperature for your address, then check the equipment’s output at 5°F rather than its nominal tonnage. A unit sold as three tons can deliver far less on a zero-degree night, and that gap is where strip heat takes over. See [heat pump sizing](https://clementbostonheatpumps.com/guide/heat-pump-sizing/).

### Backup heat, set on purpose

Electric backup strips cost about as much to run as baseboard. We set the lockout so they only come on when the heat pump can’t hold the house, and we record that setting at commissioning; our [aux heat guide](https://clementbostonheatpumps.com/guide/heat-pump-aux-heat/) explains the choices.

## Dual fuel is still allowed in Bedford

Bedford is a comparison community in the state’s fossil-fuel-free program, not a participant. A heat pump paired with a gas furnace stays allowed here, even in major renovations, subject to the energy code.

### When keeping the furnace makes sense

If your gas furnace is only a few years old, a [dual fuel heat pump](https://clementbostonheatpumps.com/dual-fuel-heat-pump/) sits on top of it and lets the furnace take the coldest hours. Mass Save’s partial-home rebate covers that design at $1,125 per ton up to $8,500, with integrated controls required.

### When it doesn’t

If the furnace is near the end, replacing it outright earns more. Mass Save’s whole-home rebate pays $2,650 per ton up to $8,500, as long as the old furnace comes out or is disconnected; see [furnace to heat pump conversion](https://clementbostonheatpumps.com/furnace-to-heat-pump-conversion/).

### The specialized code

Bedford has used the specialized energy code since July 1, 2024. It shapes new homes and major renovations, while a heating replacement in an existing house stays a mechanical job.

## Bedford’s houses, from the Depot to the newer streets

Fewer than one Bedford home in ten predates 1940, and about two-thirds are detached houses. Gas heats about 60% of homes, by furnace or by boiler, and the heating plant decides how the ducts get planned.

### Split-levels and colonials with ducts

A warm-air furnace with central air leaves the supply trunk and returns behind. Heat pump air leaves the coil cooler than furnace air, so the blower pushes more of it; we read static pressure across the system and check each return grille. Where one return is too small, we add one rather than oversize the equipment.

### Homes on hot-water baseboard

Where a house heats with a boiler and baseboard loops, there’s no duct to reuse. A basement air handler serves the first floor and an attic unit the bedrooms; see [boiler to heat pump conversion](https://clementbostonheatpumps.com/boiler-to-heat-pump-conversion/).

### Townhouses and condos

About 17% of Bedford homes are in complexes of five units or more, and another 4.5% share a three- or four-unit building. The association decides where the outdoor unit goes, so we bring a placement plan early; our [condo guide](https://clementbostonheatpumps.com/guide/condo-heat-pump-replacement/) covers that approval.

## What a heat pump costs to run on Eversource

Bedford homes on Eversource can use its seasonal heat pump rate, which lowers distribution and transmission charges on all household kilowatt-hours from November 1 to April 30.

- **Oil or propane today:** with the winter rate in place, delivered heat from a cold-climate unit comes in below the burner’s cost, and the truck stops coming. [Heat pump vs oil](https://clementbostonheatpumps.com/guide/heat-pump-vs-oil-heat/) lays out the arithmetic.
- **Baseboard today:** a resistance heater turns one kilowatt-hour into one unit of heat, while the heat pump moves two or more on most winter days; see [baseboard to heat pump](https://clementbostonheatpumps.com/baseboard-heat-to-heat-pump/).
- **Gas today:** per BTU, gas stays cheaper, so the reasons to switch are central cooling, an aging furnace or a cold upstairs.

Homes that receive a Mass Save heat pump rebate are normally moved onto the rate without asking. Because Hanscom-side winters run longer, the rate’s six months cover nearly all of the heating season; the [winter rate guide](https://clementbostonheatpumps.com/guide/heat-pump-electric-rate-massachusetts/) explains enrollment.

## Bedford paperwork: permits, utility and rebates

The town’s building department issues the electrical permit and, where ducts or gas lines change, sheet metal and gas permits. Its filing route, and any local setback or sound rule for the outdoor unit, is confirmed per address.

| What | The Bedford figure |
| --- | --- |
| Electric utility | Eversource |
| Gas company | National Grid (Boston Gas) |
| Energy code | Specialized code since July 1, 2024 |
| Fossil-fuel-free program | Comparison community; dual fuel allowed |
| Heating fuel | Gas 60.2%, oil 21.9%, electricity 13.4%, propane 4.3% |
| Mass Save whole-home rebate | $2,650 a ton, capped at $8,500, on installs through December 31, 2026 |

Systems installed on or after January 1, 2027 earn $2,350 a ton, capped at $7,500. Cold-climate listed equipment and proof of weatherization are part of the deal; the [rebate guide](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/) has the full list.

## The order of work in a Bedford house

We start at the house: a Manual J for your rooms, static readings on the ducts, the electrical panel, and the yard, where the outdoor unit needs a spot out of drifting snow and roof drip.

1. **Estimate in writing:** the unit and what it delivers at 5°F, any return or duct changes, the electrical work, permits, and whether you’re on the whole-home or partial-home rebate.
2. **Permits pulled,** then two to five working days on site when the ducts can stay.
3. **The furnace question settled:** taken out and the gas capped for whole-home, or tied to integrated controls for dual fuel.
4. **Start-up checks:** nitrogen pressure test, evacuation under 500 microns, refrigerant weighed in for the line length, airflow and static measured, strip heat lockout written down.

[Concord](https://clementbostonheatpumps.com/service-areas/concord/) next door runs its own light plant rebate, and [Billerica](https://clementbostonheatpumps.com/service-areas/billerica/) to the north is on National Grid.

## Services in Bedford

- [Service**Furnace to heat pump conversion** Take out the gas or propane furnace and heat and cool through the same ducts with a heat pump.](https://clementbostonheatpumps.com/furnace-to-heat-pump-conversion/)
- [Service**Whole-home heat pumps** One ducted system that heats and cools the whole house, with the furnace or boiler retired.](https://clementbostonheatpumps.com/whole-home-heat-pump/)
- [Service**Dual fuel heat pumps** A heat pump paired with the furnace you keep, with one control deciding which one heats.](https://clementbostonheatpumps.com/dual-fuel-heat-pump/)
- [Service**Boiler to heat pump conversion** New ducts or small-duct high-velocity runs so a heat pump can heat and cool a radiator house.](https://clementbostonheatpumps.com/boiler-to-heat-pump-conversion/)
- [Service**Baseboard heat to heat pump** Replace electric baseboard with a ducted heat pump that heats on far less electricity and cools too.](https://clementbostonheatpumps.com/baseboard-heat-to-heat-pump/)

## How a job usually runs in Bedford

### First call

You tell us what heats and cools the house now, which rooms aren't working, and roughly where the house is.

### Home visit

We measure the house for a load calculation, test the ducts, check the panel and look for an outdoor spot.

### Written estimate

Equipment, duct changes, electrical, permits and the rebate path, line by line, with our price.

### Install

Permits first, then the work: usually two to five working days on site.

### Commissioning

Pressure test, vacuum, charge by weight, airflow and controls set before we call it done.

## Neighborhoods, landmarks and routes

- Bedford Center
- Bedford Depot
- Hanscom area

### Landmarks

- Hanscom Field
- Bedford Depot Park
- Minuteman Bikeway
- Shawsheen River
- Concord River

### Getting around

- Route 4
- Route 225
- Route 62
- Route 3

[Open Bedford, MA in Google Maps](https://www.google.com/maps/search/?api=1&query=Bedford%2C%20MA)

## Bedford: questions

### Do Bedford's colder winter nights mean I need a bigger heat pump?

Not a bigger one, a better-checked one. We size from a room-by-room load calculation at your address's design temperature, then confirm the unit's capacity at 5°F. Hanscom Field averages about five nights a year at or below 0°F, so that low-temperature number matters more here than in Boston.

### Can I add a heat pump and keep my gas furnace in Bedford?

Yes. Bedford is a comparison community in the state's fossil-fuel-free program, not a participant, so a heat pump paired with a gas furnace stays allowed, even in major renovations, subject to the energy code. Mass Save's partial-home rebate needs integrated controls that run both.

### What does a heat pump cost for a Bedford house on a gas furnace?

Where the existing ducts can be reused, our typical range for a whole-home system is $15,000 to $28,000 and up before rebates. Bedford is on Eversource, so Mass Save's whole-home rebate of $2,650 per ton up to $8,500 applies through December 31, 2026. Your written estimate sets the price.

### Does Eversource's winter heat pump rate apply in Bedford?

Yes. From November 1 to April 30 it lowers distribution and transmission charges on all your household kilowatt-hours. Mass Save heat pump rebate recipients are usually enrolled automatically; otherwise you can ask Eversource to switch the account.

### Does Bedford's specialized energy code affect replacing my heating system?

Bedford has followed the specialized code since July 1, 2024. It sets requirements for new homes and major renovations, not a like-for-like heating replacement, which stays a mechanical job with the usual electrical and sheet metal permits.

## Nearby service areas

- [Service area**Concord** Ducted heat pumps for Concord homes, sized at the 8°F design point Concord Light's whole-home rebate asks for and planned around the fossil-fuel-free by-law.](https://clementbostonheatpumps.com/service-areas/concord/)
- [Service area**Lexington** Cold-climate ducted heat pumps for Lexington homes on oil, propane or gas, sized for Hanscom-area winters and planned around the town's fossil-fuel-free bylaw.](https://clementbostonheatpumps.com/service-areas/lexington/)
- [Service area**Billerica** Ducted heat pumps for Billerica's gas-heated ranches and colonials, with Mass Save rebates through National Grid, the stretch code and online permits.](https://clementbostonheatpumps.com/service-areas/billerica/)

## Guides for houses in Bedford

- [Learn**What size heat pump do I need?** Why square footage and the old unit's tonnage both mislead, what a room-by-room load calculation measures, and how the result turns into equipment.](https://clementbostonheatpumps.com/guide/heat-pump-sizing/)
- [Learn**Why does my heat pump's aux heat keep coming on?** Backup heat is part of every cold-climate system. Here's when it should run, when it shouldn't, and the settings that decide which.](https://clementbostonheatpumps.com/guide/heat-pump-aux-heat/)
- [Learn**How does the heat pump electric rate work in Massachusetts?** Which part of your electric bill the seasonal rate lowers, why it applies to the whole house, how enrollment works, and what it means for the switch from oil or gas.](https://clementbostonheatpumps.com/guide/heat-pump-electric-rate-massachusetts/)
- [Decision Guide**What's involved in replacing a heat pump in a condo?** In a condo, the outdoor unit usually sits on common property, so the association, the master deed and sometimes a historic commission come before equipment.](https://clementbostonheatpumps.com/guide/condo-heat-pump-replacement/)
- [Learn**How do Mass Save heat pump rebates work?** The three rebate tiers, the conditions behind each, the dates that change them, and what happens in towns with their own light plant.](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/)

## Get an estimate in Bedford

Tell us what heats the house now and which rooms aren't working in Bedford.

(857) 837-1475
