# Heat pump ductwork in Boston, MA

> Ducts tested and fixed for heat pump airflow: static pressure, return size and leakage measured, then returns added, trunks sealed and runs resized.

URL: https://clementbostonheatpumps.com/heat-pump-ductwork/

Service

Duct testing, sealing, new returns and resized runs so a heat pump gets the air it needs.

(857) 837-1475

Last Updated: November 12, 2026

Sized

From a room-by-room load calculation at your town's design temperature

Measured

Duct static pressure and airflow before and after

Tested

Nitrogen pressure test and deep vacuum before the charge

In writing

Equipment, duct work, electrical and permits listed line by line

## What a heat pump ductwork job in Wollaston looks like

The panned joist return opened up along the basement ceiling

New sheet metal return trunk and sealed supply seams

### What the test shows

A 1925 Wollaston colonial getting ready to swap its gas furnace for a 3-ton heat pump. At 1,050 cfm the ducts read 0.95 inch of static, nearly double what the air handler is rated for. One 12 by 6 return grille in the downstairs hall serves the whole house.

### Where the air goes missing

The lone return runs through a panned joist bay that leaks along every joint, and the supply trunk has open seams and a loose end cap. Three upstairs branch runs are crushed flat where they pass the chimney. A leakage test reads 340 cfm25 before anything changes.

### The fixes

A 20 by 20 filter grille goes in upstairs, fed through a chase in the hall closet. The first-floor return grows to 20 by 14, and about 22 feet of sheet metal replaces the panned bay. Every trunk seam gets mastic, the crushed runs are replaced and each branch gets a damper.

### Ready for the heat pump

After the work, static reads 0.48 inch at the same airflow and leakage drops to 120 cfm25. Those numbers go in writing for the heat pump startup. The sheet metal permit is filed through Quincy's online portal, and the duct work is priced as its own line.

*Project facts*

| Service | Heat pump ductwork |
| --- | --- |
| Where | Wollaston, Quincy |
| House | 1925 colonial, about 1,650 sq ft |
| Before | One 12 x 6 return; static 0.95 inch |
| After | Two returns, sealed trunk; static 0.48 inch |
| Price | $6,200 for the duct work |
| Time on site | Two working days |

Your furnace ducts were sized for hot, fast air from a burner. A heat pump delivers cooler air in larger volume, so ducts that seemed fine can become the reason a new system feels weak. [Clement Boston Heat Pumps](https://clementbostonheatpumps.com/) tests and fixes heat pump ductwork across Boston and nearby towns, before the new system starts.

We price duct work as its own line on the estimate, from what the static test and inspection find. Returns added, trunks sealed and runs replaced each show up separately.

## Can a heat pump use the ducts you already have?

Often, with changes. Whether yours can depends on three things we measure on the first visit: static pressure, return size and leakage.

### Why heat pumps are harder on ducts

A gas furnace can send air out at 120°F or more. A heat pump sends it closer to body temperature and makes up the difference with volume, about 350 to 400 cubic feet per minute per ton. Ducts that were marginal for the furnace end up choked.

### Equipment and ducts are one decision

A variable-speed blower tolerates a bit more resistance than a fixed-speed one. A right-sized heat pump moves less air than an oversized one, which can let existing ducts work unchanged. We choose the equipment and the duct changes together, from the [load calculation](https://clementbostonheatpumps.com/guide/heat-pump-sizing/).

## What we check in the ducts on the first visit

The duct check takes about an hour of the home visit. We test the system running, then follow the ducts from the air handler to the farthest register.

- **Static pressure** on both sides of the blower, with the filter in place.
- **Return area**: how many grilles, how big, and whether a panned bay or a closet carries the air back.
- **Trunk and takeoffs**: open seams, missing end caps, loose collars and crushed runs.
- **Register flow** in the rooms you say are weak, compared with what their heat loss needs.
- **Ducts in unheated space**: attic or garage runs, their insulation and their supports.
- **The filter rack**: a 1-inch filter jammed into a narrow slot can cost a tenth of an inch of static on its own.

Those findings go on the estimate as separate lines, each with the reason it’s there, so you can see which changes the new system depends on and which are worth doing anyway.

## Static pressure, in plain words

Static pressure is how hard the blower pushes against the ducts, filter and coil. We read it with a manometer on the supply and return sides of the air handler, in inches of water column.

Many residential air handlers are rated for 0.5 inch of total external static. Above that, a variable-speed blower ramps up to hold airflow, gets louder and draws more power, then runs out of room. A reading of 0.8 or 0.9 inch means the ducts are choking the system.

### What a high reading causes

- Whistling registers and a loud air handler.
- Weak flow in the rooms farthest from the unit.
- An indoor coil that ices in summer.
- A heat pump that trips on high pressure during winter heating.
- Higher bills from blower power and [backup strips](https://clementbostonheatpumps.com/guide/heat-pump-aux-heat/).

## Returns: where the air comes back

A house with one return grille for the whole system, often a panned joist bay in the basement ceiling, starves a heat pump of air. Supply only works as well as the return lets it.

We size returns for the new system’s airflow at a face velocity low enough to stay quiet. That can mean a second return upstairs through a closet chase, a larger filter grille, or a panned bay rebuilt in sheet metal. Closed bedroom doors need a way back too: a jumper duct or transfer grille.

## Leaks and how we seal them

Leaky ducts lose air to the basement, the attic or the wall cavities. In a basement some of that heat still reaches the house; in an attic it’s gone.

- Every reachable seam, takeoff, end cap and boot inspected by eye and by hand.
- A duct leakage test with a calibrated fan where the job or program calls for a number.
- Sealing with mastic or listed foil tape, never cloth duct tape.
- At least R-8 insulation on ducts that run through an attic.

Panned joist returns leak along every joint in the bay and pull dusty basement air into the system. Rebuilding them in sheet metal fixes both problems. Older houses add plaster and framing puzzles; see [heat pumps in old houses](https://clementbostonheatpumps.com/guide/heat-pumps-in-old-houses/).

## Sizing new runs with Manual D

When runs change, we size them with ACCA Manual D. It matches each run to its room’s heat loss from the Manual J and to the pressure the blower has available.

In practice, each room gets the airflow its load calls for, not whatever its old run happened to carry. A bedroom over a garage may need a bigger run; a kitchen may need a smaller one. Balancing dampers at the takeoffs let us trim each room at startup.

## When the ducts can’t be saved

Boiler-heated houses have no ducts, and some ducts are too small, crushed or damaged to reuse. A new duct system is a bigger job, priced on its own.

Our typical range for a heat pump with a new duct system, including small-duct high-velocity designs for boiler homes, is $20,000 to $40,000 and up. See [boiler to heat pump conversion](https://clementbostonheatpumps.com/boiler-to-heat-pump-conversion/) and [baseboard heat to heat pump](https://clementbostonheatpumps.com/baseboard-heat-to-heat-pump/). Ducts wrapped in old white tape or paper may contain asbestos and get tested before anyone cuts.

## Permits and the numbers you get back

Duct work is sheet metal work and needs a sheet metal permit. Boston charges $20 plus $25 per 200 feet; Cambridge charges $50 plus $25 per 100 feet and triples fees for work started before the permit.

The closeout lists static pressure before and after, measured airflow at the air handler and any damper settings. Towns such as [Quincy](https://clementbostonheatpumps.com/service-areas/quincy/) file permits through an online portal. The duct work fits into the full [installation process](https://clementbostonheatpumps.com/guide/heat-pump-installation-process/), usually ahead of a [whole-home heat pump](https://clementbostonheatpumps.com/whole-home-heat-pump/) or a [furnace conversion](https://clementbostonheatpumps.com/furnace-to-heat-pump-conversion/).

## What's included

- Static pressure readings across the existing system before any change
- A walk of every reachable trunk, takeoff, return and register
- Return capacity sized to the new system's airflow
- Leaks sealed at seams, takeoffs, end caps and boots
- Panned joist returns rebuilt in sheet metal where they leak
- Crushed or undersized branch runs replaced, with balancing dampers
- Readings repeated after the work, with before and after written down

## What happens to the ducts you have

|  | Use as they are | Modify and seal | New duct system |
| --- | --- | --- | --- |
| Static pressure reading | At or under the equipment rating | Above it, from returns or leaks | Ducts too small or too damaged to fix |
| Typical work | Filter and register check | Returns added, trunk sealed, runs replaced | Full design and installation |
| Walls opened | None | A chase or closet for a return | Several, or small-duct runs |
| How we price it | Part of the system price | Its own line on the estimate | Our new-duct range |

## Related resources

- [Learn**What size heat pump do I need?** Why square footage and the old unit's tonnage both mislead, what a room-by-room load calculation measures, and how the result turns into equipment.](https://clementbostonheatpumps.com/guide/heat-pump-sizing/)
- [Learn**What happens during a heat pump installation?** Each step in a ducted install depends on the one before it. Here's the order, why it runs that way, and how you can tell the job was done right.](https://clementbostonheatpumps.com/guide/heat-pump-installation-process/)
- [Decision Guide**Will a heat pump work in an old house?** Boston has one of the oldest housing stocks in the country. Age changes how a heat pump goes in, not whether it can heat the house.](https://clementbostonheatpumps.com/guide/heat-pumps-in-old-houses/)
- [Decision Guide**Should I get a ducted or ductless heat pump?** Both are heat pumps. The difference is how the heat reaches each room, and that comes down to the ducts you have or could add.](https://clementbostonheatpumps.com/guide/ducted-vs-ductless-heat-pump/)
- [Decision Guide**What questions should I ask a heat pump installer before I sign?** Two quotes for the same house can describe very different jobs. These questions show you which one you're actually buying.](https://clementbostonheatpumps.com/guide/heat-pump-quote-checklist/)

## How a job runs

### First call

You tell us what heats and cools the house now, which rooms aren't working, and roughly where the house is.

### Home visit

We measure the house for a load calculation, test the ducts, check the panel and look for an outdoor spot.

### Written estimate

Equipment, duct changes, electrical, permits and the rebate path, line by line, with our price.

### Install

Permits first, then the work: usually two to five working days on site.

### Commissioning

Pressure test, vacuum, charge by weight, airflow and controls set before we call it done.

## Heat pump ductwork: questions

### Will my old furnace ducts be big enough for a heat pump?

Sometimes as they are, often with changes. A heat pump moves more air than a furnace to deliver the same heat at a lower supply temperature. We measure static pressure and look at return size before the estimate, and a right-sized heat pump sometimes fits the ducts without changes.

### What static pressure reading is too high for a heat pump?

Anything above the air handler's rated external static pressure, which is 0.5 inch of water column on many residential units. At 0.8 or 0.9 inch, the blower works hard, gets noisy and still falls short of the airflow the heat pump needs.

### Do I need more return vents for a heat pump?

If the house has one small return, likely yes. Returns are sized to the system's airflow at a face velocity low enough to stay quiet. That can mean a second return upstairs, a larger filter grille, or transfer grilles so closed bedrooms still breathe.

### Is duct sealing worth doing before a heat pump goes in?

Yes, in most houses. Leaks in a basement trunk pull dusty air into the system and push heat where you don't need it; leaks in an attic lose it outright. Sealing before startup means the airflow we measure is the airflow your rooms get.

### How do you price duct work for a heat pump?

As its own line on the estimate, from what the tests and inspection find, meaning the number of returns added, the feet of trunk sealed, the runs replaced and the access to reach them. A whole new duct system is priced in our new-duct range instead.

## Related services

- [Service**Whole-home heat pumps** One ducted system that heats and cools the whole house, with the furnace or boiler retired.](https://clementbostonheatpumps.com/whole-home-heat-pump/)
- [Service**Furnace to heat pump conversion** Take out the gas or propane furnace and heat and cool through the same ducts with a heat pump.](https://clementbostonheatpumps.com/furnace-to-heat-pump-conversion/)
- [Service**Air handler replacement** A new indoor unit matched to the outdoor heat pump you already have.](https://clementbostonheatpumps.com/heat-pump-air-handler-replacement/)

## Get an estimate for heat pump ductwork

Tell us what heats it now and which rooms aren't working. We'll measure, lay out the system and the ducts, and put the plan and the price in writing.

(857) 837-1475
