# How much does heat pump installation cost in Massachusetts?

> What a ducted heat pump costs in the Boston area, what moves the price, the permit fees and wages behind it, and the rebates and loans that change what you pay.

URL: https://clementbostonheatpumps.com/guide/heat-pump-installation-cost-massachusetts/

Cost Guide

Our typical ranges for Boston-area ducted heat pump jobs, what's inside the price, and what rebates do to it.

Last Updated: November 12, 2026

The short answer

Our typical range for a whole-home ducted heat pump on ducts we can reuse is $15,000 to $28,000 and up before rebates. With new ductwork or a small-duct system, it's $20,000 to $40,000 and up. Replacing an existing heat pump runs $12,000 to $24,000. The load calculation, the ducts, the panel and the outdoor spot set your number.

Key takeaways

- Tonnage from a load calculation, duct work, line length, the panel and the outdoor spot move the price most.
- Mass Save pays its whole-home rebate per ton through participating contractors; light plant towns run their own programs.
- Boston-area HVAC installers earn about 23% more than the national average, which is part of why national price figures run low here.
- The federal heat pump tax credit ended for systems placed in service after December 31, 2025.

## Our typical ranges

[Clement Boston Heat Pumps](https://clementbostonheatpumps.com/) prices every job from a home visit and a written estimate. These are our typical ranges for the jobs we’re asked about most, before any rebate.

| Job | What it covers | Our typical range |
| --- | --- | --- |
| [Whole-home heat pump](https://clementbostonheatpumps.com/whole-home-heat-pump/), ducts reused | Cold-climate outdoor unit on a snow stand, matched air handler or coil, line set, circuit, controls, permits, old system removed | $15,000 to $28,000 and up |
| [Heat pump replacement](https://clementbostonheatpumps.com/heat-pump-replacement/) | Swap of an existing ducted heat pump, line set reused where it tests sound | $12,000 to $24,000 |
| Heat pump with [new ductwork](https://clementbostonheatpumps.com/boiler-to-heat-pump-conversion/) | Attic or basement air handlers with new duct runs, or a small-duct high-velocity system | $20,000 to $40,000 and up |
| [Electrical service upgrade](https://clementbostonheatpumps.com/electrical-panel-upgrade-for-heat-pump/) | Typically 100 to 200 amps, customer side, with utility coordination | $3,000 to $6,500 |
| [Oil tank removal](https://clementbostonheatpumps.com/oil-tank-removal/) | Accessible basement tank, emptied and removed, plus the Boston Fire Department permit | $600 to $1,500 |
| [Air handler replacement](https://clementbostonheatpumps.com/heat-pump-air-handler-replacement/) | Air handler matched to an existing outdoor unit | $1,500 to $4,200 and up |

The open-ended tops are real. A large house, a long line set to a roof, a crane day or extensive duct work can push a job past the top of a range, and we say so on the estimate rather than squeezing the scope to fit a number.

## What moves the price

Six things account for most of the difference between two jobs that sound the same.

| What changes | Why it moves the price |
| --- | --- |
| Tonnage from the load calculation | Equipment is priced by capacity, and a proper calculation often lands smaller than the old unit |
| Ducts | Reusing sound ducts is cheapest; a bigger return, sealing or a new trunk adds; new duct systems add the most |
| Line set length and route | A 20-foot run through a basement wall is simple; a 40-foot run to a roof or attic needs a cover and more labor |
| Panel and service | Two new 240-volt circuits on a panel with room is routine; a service upgrade adds $3,000 to $6,500 |
| Outdoor spot | A ground stand is the baseline; porches, roofs and wall brackets add hardware, and sometimes a crane |
| Permits and review | Electrical, sheet metal and gas permits, plus historic or condo review where it applies |

The efficiency tier matters less than people expect. For a Boston house, compare capacity at 5°F across models; most cold-climate ducted units are already [variable speed](https://clementbostonheatpumps.com/guide/variable-speed-heat-pump/). Our guide to [SEER2 and HSPF2](https://clementbostonheatpumps.com/guide/seer2-hspf2-ratings/) explains the labels.

## What’s inside a Boston heat pump price

A heat pump estimate is roughly half equipment, about a third labor and around a tenth electrical work, with permits, materials and removal making up the rest. The public figures behind those parts:

| Part of the price | What sets it | Local figure |
| --- | --- | --- |
| HVAC labor | Installer wages in the metro | U.S. Bureau of Labor Statistics: HVAC mechanics and installers in the Boston-Cambridge-Newton area earn a mean $38.41 an hour, about 23% above the $31.14 national mean |
| Electrical labor | Electrician wages | Electricians in the same area earn a mean $40.08 an hour, about 17% above the $34.37 national mean |
| Electrical permit (Boston) | City of Boston Inspectional Services fee schedule | Service upgrade: $20 plus $0.25 per amp, so $70 for 200 amps |
| Sheet metal permit (Boston) | City of Boston fee schedule | $20 plus $25 per 200 linear feet of duct |
| Building permit, short form (Boston) | City of Boston fee schedule | $20 plus $10 per $1,000 of work, so $300 on a $28,000 job |
| Oil tank removal permit (Boston) | Boston Fire Department | $110 |
| Wall, ceiling and finish repair | Your house | Priced on the estimate: we list every opening and its repair |

A wage is not a billing rate: the hourly price on any invoice also carries insurance, licensing, vehicles, tools and overhead. The wage gap is still a fair guide to why Boston prices run above national averages.

Other towns set their own permit fees. Cambridge, for example, charges $50 plus $25 per 100 linear feet for a sheet metal permit, and triple fees for work started before a permit is issued.

## Rebates, loans and what they do to the price

Mass Save’s per-ton rebates and its 0% HEAT Loan are the big ones; towns with their own light plant run their own programs. The federal heat pump credit is gone.

| Program | Who runs it | Amount | What it needs |
| --- | --- | --- | --- |
| Whole-home heat pump rebate | Mass Save sponsors | $2,650 per ton up to $8,500 for systems installed through 2026; $2,350 per ton up to $7,500 from January 1, 2027 | Cold-climate listed equipment, a participating installer in the Heat Pump Installer Network, old system removed or disconnected, proof of weatherization |
| Partial-home rebate (dual fuel) | Mass Save sponsors | $1,125 per ton up to $8,500; $1,000 per ton up to $7,500 from January 1, 2027 | Integrated controls that hand off to the furnace at or below the maximum switchover temperature |
| Basic rebate, including replacing an existing heat pump | Mass Save sponsors | $250 per ton up to $2,500 | Qualifying equipment |
| Income-eligible rebates | Mass Save sponsors | Up to $16,000 for whole-home | Household income limits |
| HEAT Loan | Mass Save, through participating lenders | 0% interest, up to $25,000 | Eligible measures, applied for before the work |
| Light plant programs | Belmont, Reading, Braintree, Wellesley, Concord, Hingham and other town utilities | Varies; for example Belmont Light pays $1,000 per ton up to $5,000 for oil and propane switches | Each town’s own rules |
| Federal 25C tax credit | IRS | Ended | Not available for systems placed in service after December 31, 2025 |

Rebates come after the work. On the whole-home path through 2026, a 3-ton system earns $7,950, and anything from about 3.25 tons up reaches the $8,500 cap. We confirm which program your address falls under before we write the estimate; see [Mass Save heat pump rebates](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/) and the [HEAT Loan](https://clementbostonheatpumps.com/guide/mass-save-heat-loan-heat-pump/).

## Three typical budgets

Three typical jobs, priced from our ranges. Each shows how scope, not house size, sets the price.

### A Roslindale colonial on two duct systems: $27,400

A gas furnace and a 4-ton attic AC replaced by a 2-ton basement heat pump and a 1.5-ton [attic heat pump](https://clementbostonheatpumps.com/attic-air-handler-heat-pump/), with a second return added and the attic ducts rebuilt. Four working days on site.

### A Jamaica Plain oil conversion: $28,300

A 3-ton whole-home heat pump on the existing furnace ducts, the return enlarged, the service upgraded to 200 amps and the oil tank removed. Five working days on site. See [heat pump vs oil heat](https://clementbostonheatpumps.com/guide/heat-pump-vs-oil-heat/).

### A Mid-Cambridge renovation with new ducts: $36,800

A steam boiler replaced by a 2-ton attic system and a 1.5-ton basement system on new ducts, timed to a renovation in [Cambridge](https://clementbostonheatpumps.com/service-areas/cambridge/). Nine working days on site.

## How to compare quotes

Compare what each quote includes, not the bottom number. The lines below are the ones that most often go missing.

- The equipment model and its capacity at 5°F
- Whether a [load calculation](https://clementbostonheatpumps.com/guide/heat-pump-sizing/) was done
- Duct changes, listed one by one
- Electrical work, and who pulls which permits
- Whether the installer is in Mass Save’s network

If a line is blank, ask before you compare; our [quote checklist](https://clementbostonheatpumps.com/guide/heat-pump-quote-checklist/) has the full list. For a number for your own house, call us or send the form, and we’ll measure and send it in writing.

## Questions about this guide

### Why do online heat pump prices look so much lower than Boston quotes?

Most national figures describe a simpler job: a like-for-like swap on good ducts, in a market where installers earn less. Boston-area jobs more often include duct changes, a service upgrade, old-house access and permits in several trades, and local labor costs more.

### Is a heat pump cheaper than replacing a furnace and AC?

Usually it costs more up front than a basic furnace and AC pair, but less once Mass Save's whole-home rebate comes off, and it can lower running cost if you heat with oil. Against gas, the running cost is closer; we put both on the estimate.

### Do rebates come off the price at the start?

No. Mass Save rebates are paid after the job, once the paperwork is approved. Mass Save's 0% HEAT Loan can cover the cost up front through a participating lender, which is why many owners pair the two.

## Related service

- [Service**Whole-home heat pumps** One ducted system that heats and cools the whole house, with the furnace or boiler retired.](https://clementbostonheatpumps.com/whole-home-heat-pump/)

## More guides

- [Learn**How do Mass Save heat pump rebates work?** The three rebate tiers, the conditions behind each, the dates that change them, and what happens in towns with their own light plant.](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/)
- [Learn**How does the Mass Save HEAT Loan work for a heat pump?** A 0% loan through participating banks and credit unions, the steps that have to happen before the work starts, and where it stops covering a job.](https://clementbostonheatpumps.com/guide/mass-save-heat-loan-heat-pump/)
- [Learn**What size heat pump do I need?** Why square footage and the old unit's tonnage both mislead, what a room-by-room load calculation measures, and how the result turns into equipment.](https://clementbostonheatpumps.com/guide/heat-pump-sizing/)
- [Decision Guide**Is a heat pump better than oil heat in Massachusetts?** Running cost worked out from Massachusetts fuel prices and winter heat pump rates, plus the comfort, cooling, tank and hot water questions that come with the switch.](https://clementbostonheatpumps.com/guide/heat-pump-vs-oil-heat/)
- [Decision Guide**What questions should I ask a heat pump installer before I sign?** Two quotes for the same house can describe very different jobs. These questions show you which one you're actually buying.](https://clementbostonheatpumps.com/guide/heat-pump-quote-checklist/)

## Get an estimate for your house

(857) 837-1475
