# Commercial heat pump installation in Boston, MA

> Rooftop packaged heat pumps, ducted split systems for offices and shops, and a system per unit in small multifamily buildings around Boston.

URL: https://clementbostonheatpumps.com/commercial-heat-pump-installation/

Service

Rooftop packaged units, ducted splits for small offices and shops, and per-unit systems in small multifamily buildings.

(857) 837-1475

Last Updated: November 12, 2026

Sized

From a room-by-room load calculation at your town's design temperature

Measured

Duct static pressure and airflow before and after

Tested

Nitrogen pressure test and deep vacuum before the charge

In writing

Equipment, duct work, electrical and permits listed line by line

## What a commercial heat pump job in Brighton looks like

The old gas rooftop units on their curbs before the lift

New packaged heat pump set on a flashed curb adapter

### The building and the problem

A single-story dental office near Brighton Center runs on two rooftop units from the mid-2000s, a 5-ton and a 4-ton, with gas heat and R-22 cooling. One heat exchanger is cracked, the cooling side needs refrigerant every summer, and the treatment rooms swing warm and cold while patients sit still.

### What the load calculation changes

The load counts about 300 cubic feet a minute of outdoor air the office has to bring in. Even so, the building needs 8 tons, not 9: a 5-ton packaged heat pump for the treatment wing and a 3-ton unit for the front office, each with electric heat sized for Boston's 7°F design night.

### Crane day

On Friday after the last patient, a licensed gas fitter caps both gas lines and the old refrigerant is recovered. On Saturday a boom truck in the rear lot lifts the old units off, curb adapters go onto the existing curbs and are flashed into the membrane, and the new units are set. No new roof openings.

### Wiring, controls and startup

On Monday the 5-ton circuit goes from 60 to 80 amps on the building's 208-volt three-phase service. Thermostats follow office hours with a shallow night setback, and the strips lock out above 25°F except in defrost. Mass Save's commercial pre-approval, 8 tons at $2,000 a ton, is in hand before ordering.

*Project facts*

| Service | Commercial rooftop heat pumps |
| --- | --- |
| Where | Brighton, near Brighton Center |
| Building | Single-story dental office, about 3,000 sq ft |
| Before | Two gas-heat rooftop units, 9 tons |
| After | 5-ton and 3-ton packaged heat pumps |
| Price | $61,800 before rebates |
| Time on site | Three working days, crane on a Saturday |

Two rooftop units past 20 years old, gas for the heat, and a repair call every summer for the cooling. [Clement Boston Heat Pumps](https://clementbostonheatpumps.com/) handles commercial heat pump installation for buildings like that: small offices, shops and clinics, plus small apartment and condo buildings, across Boston and the towns around it.

We work on three kinds of system: packaged rooftop heat pumps, ducted split systems, and one system per apartment. Each job is priced from a site visit and a written estimate, because tonnage, roof access and the electrical service move the number more than the unit does.

## Which commercial system fits your building?

The building usually decides. Rooftop units now means a packaged heat pump on the same curb. An air handler inside means a split system. Apartments get a system each.

### Rooftop packaged heat pumps

A packaged unit holds the compressor, both coils, the fan and the controls in one cabinet. It sits on a roof curb over the supply and return ducts. Swapping a gas-fired rooftop unit for a heat pump keeps the ducts and the roof opening, and puts electric heat where the gas burner was.

Curbs differ from maker to maker, so most swaps need a curb adapter: a sheet metal transition that fits the new footprint to the old openings without a new hole in the roof.

### Ducted split systems

An office or storefront with its air handler above the ceiling or in a closet gets a split system. The outdoor unit goes on the roof or at grade, a copper line set runs to the indoor air handler, and the existing ducts stay if they carry enough air.

Line length and the route through the building set much of the price.

### One system per apartment

In a small apartment or condo building, each unit gets its own ducted heat pump on its own meter. Outdoor units go on the roof or in the rear yard, and every line set through a floor gets fire-rated sealing.

Our [triple-decker guide](https://clementbostonheatpumps.com/guide/triple-decker-heat-pumps/) covers the layouts, and the [condo replacement guide](https://clementbostonheatpumps.com/guide/condo-heat-pump-replacement/) covers working with an association.

## What happens on the site visit

We look at the roof, the mechanical spaces and the electrical service, read the nameplates on what’s there, and work out the load. All of it goes into one written estimate.

- **The load.** A commercial building has to bring in outdoor air for ventilation. In January that air arrives in single digits and has to be heated, so a clinic or a shop with a busy door needs more heat than its floor area suggests.
- **The roof or the ceiling.** Curb size and condition, the membrane around each curb, the crane’s path, and whether a ceiling can open for an air handler and line set.
- **The electrical service.** Voltage and phase (small commercial buildings often run 208-volt three-phase), the service size, and breaker room for units with electric heat. If the service is short, an [upgrade](https://clementbostonheatpumps.com/electrical-panel-upgrade-for-heat-pump/) goes on the estimate.
- **The controls.** Occupied hours, who touches the thermostat, and whether gas heat stays as backup.

You get back the equipment and its heating capacity at the design temperature, the curb plan, the crane day, the electrical work, permits, the rebate path and our price.

## Cold nights, fresh air and backup heat

A packaged heat pump loses capacity as it gets colder, just when the ventilation air is coldest. So every commercial unit we specify carries backup heat sized for the design night, and the controls decide when it runs.

### Electric or gas backup

Most packaged heat pumps come with electric heat strips. Some buildings keep a gas section in a [dual-fuel](https://clementbostonheatpumps.com/dual-fuel-heat-pump/) rooftop unit and let the heat pump carry milder weather. If gas stays, Mass Save’s commercial rebate asks for controls that run the heat pump first, down to a set switchover temperature.

### Occupied hours

Offices set back at night. A heat pump recovering from a deep setback leans on backup heat, so we program a shallow setback and an earlier morning start instead. The [heat pump thermostat guide](https://clementbostonheatpumps.com/guide/heat-pump-thermostat/) explains the same logic for homes, and the [aux heat guide](https://clementbostonheatpumps.com/guide/heat-pump-aux-heat/) covers what the strips cost to run.

## Crane day, roof work and permits

Rooftop work runs around one fixed day: the crane. Everything else is arranged so the old units come down and the new ones go up in a single lift window.

1. **Permits first.** Electrical, sheet metal and, where the roof or structure changes, building. Some building departments ask for engineered drawings on commercial work; those are lined up before equipment is ordered.
2. **The lift plan.** Crane size and reach from the parking lot or the street. A crane in a city street needs the city’s approval to occupy it, so the day is set early.
3. **The day before.** Units disconnected, gas lines capped by a licensed gas fitter, refrigerant recovered.
4. **Lift day.** Old units off, curb adapters set and flashed into the roof, new units on.
5. **Startup.** Wiring, controls, a startup check on each unit and the occupied schedule set.

A newer gas rooftop unit with years left doesn’t have to come off. When one is worth keeping, the estimate says so.

## Mass Save’s commercial heat pump rebate

Mass Save pays $2,000 per ton for qualifying commercial air-source heat pumps on projects up to 35 tons, and reviews larger projects one at a time. Every commercial project needs pre-approval before installation.

| Item | What it means for you |
| --- | --- |
| Who qualifies | Buildings on a commercial account with a Mass Save electric or gas sponsor |
| Equipment | Units on Mass Save’s commercial qualified product list |
| If gas or oil stays | Integrated or certified parallel controls, so the heat pump runs first |
| Timing | A commitment letter before installation, valid for four months |

Apartments on residential electric accounts generally go through Mass Save’s residential programs; our [Mass Save rebate guide](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/) covers those, and we confirm which applies before pricing. Buildings in light plant towns such as [Peabody](https://clementbostonheatpumps.com/service-areas/peabody/) or [Braintree](https://clementbostonheatpumps.com/service-areas/braintree/) follow that utility’s programs on the electric side.

### Boston’s building emissions rules

Boston’s BERDO rules cover residential buildings with 15 or more units and non-residential buildings of 20,000 square feet or more. A small office or a six-unit building sits below those lines, but an owner who also holds a covered building can plan the two together.

## How we price commercial work

We price each building from the site visit, not from a per-ton chart. The written estimate breaks out every piece that moves the number.

- Tonnage from the load calculation, including the ventilation air
- Crane size, reach and street access, and whether the lift happens outside business hours
- Curb adapters, roof flashing and any roof repair around the curbs
- Electrical: voltage, phase, breaker room and new disconnects
- Controls, and whether gas heat stays as backup
- Permits, any drawings the building department asks for, and the pre-approval timing

For house-scale work, our [cost guide](https://clementbostonheatpumps.com/guide/heat-pump-installation-cost-massachusetts/) lists our residential ranges. A commercial building gets its own number, and the rebate comes off once the commitment letter is in hand.

## What's included

- A site visit covering the roof or mechanical space, the electrical service and the nameplates on the existing units
- A load calculation that counts the outdoor air your building brings in
- A written estimate listing equipment, curbs or adapters, the crane plan, electrical work, controls, permits and the rebate path
- Removal of old rooftop units or split equipment, with refrigerant recovered
- Curb adapters or new curbs, flashed into the roof
- Gas lines capped by a licensed gas fitter where gas heat is retired
- Thermostats or a controls schedule set to your occupied hours
- Startup checks on every unit; pressure test, vacuum, charge and measured airflow on split systems

## Three ways we put heat pumps into small commercial buildings

|  | Rooftop packaged heat pump | Ducted split system | One system per unit |
| --- | --- | --- | --- |
| Typical building | Single-story office, shop or clinic with rooftop units now | Office or storefront with an air handler above the ceiling or in a closet | A small apartment or condo building |
| Where the equipment goes | Everything in one cabinet on the roof curb | Outdoor unit on the roof or at grade, air handler inside | An outdoor unit and air handler for each apartment |
| Install day | A crane lifts the units on and off | A line set runs between the two halves | Line sets and sealed penetrations through each floor |
| Who pays the electric bill | The business | The business | Each household, on its own meter |
| What moves the price | Tonnage, curb fit, crane access | Line length, ceiling access, duct changes | Number of units, roof or yard space, fire-rated sealing |

## Related resources

- [Learn**How do Mass Save heat pump rebates work?** The three rebate tiers, the conditions behind each, the dates that change them, and what happens in towns with their own light plant.](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/)
- [Decision Guide**How do you put heat pumps in a triple-decker?** Three stacked homes under one roof, often with three owners, three meters and one narrow side yard. Here's how a heat pump job works around that.](https://clementbostonheatpumps.com/guide/triple-decker-heat-pumps/)
- [Decision Guide**What's involved in replacing a heat pump in a condo?** In a condo, the outdoor unit usually sits on common property, so the association, the master deed and sometimes a historic commission come before equipment.](https://clementbostonheatpumps.com/guide/condo-heat-pump-replacement/)
- [Learn**What thermostat do I need for a heat pump, and how should I set it?** The control decides whether a heat pump runs on its compressor or on expensive backup heat. Here's what it has to do and how to set it for a Massachusetts winter.](https://clementbostonheatpumps.com/guide/heat-pump-thermostat/)
- [Learn**Why does my heat pump's aux heat keep coming on?** Backup heat is part of every cold-climate system. Here's when it should run, when it shouldn't, and the settings that decide which.](https://clementbostonheatpumps.com/guide/heat-pump-aux-heat/)

## How a job runs

### First call

You tell us what heats and cools the house now, which rooms aren't working, and roughly where the house is.

### Home visit

We measure the house for a load calculation, test the ducts, check the panel and look for an outdoor spot.

### Written estimate

Equipment, duct changes, electrical, permits and the rebate path, line by line, with our price.

### Install

Permits first, then the work: usually two to five working days on site.

### Commissioning

Pressure test, vacuum, charge by weight, airflow and controls set before we call it done.

## Commercial heat pumps: questions

### Can a packaged heat pump go on our existing rooftop curb?

In most cases, yes, with a curb adapter. The adapter is a sheet metal transition that matches the new unit's footprint to the old supply and return openings, so the roof isn't cut again. We measure the curb and check the roofing around it on the site visit.

### Do we have to close the business for the install?

Not for long. The crane lift is the only step that needs the roof and the units off at once, and it fits in one day. We plan it for a day you're closed or a quiet morning, and the wiring and startup follow the next working day.

### Does Mass Save's commercial rebate need approval before we sign?

It needs pre-approval before installation. Since July 1, 2026, every commercial heat pump project needs a commitment letter from Mass Save before the equipment goes in, and that letter is good for four months. We set the install date inside that window.

### Can each apartment in our building have its own heat pump?

Yes, where each apartment has its own electric service. Each unit gets an outdoor unit and an air handler on that unit's meter, so each household runs its own thermostat and pays its own bill. The roof or rear yard has to hold the outdoor units with their clearances.

### How do you price a commercial heat pump job?

From the site visit. Tonnage from the load calculation, the crane and roof work, the electrical service, controls and permits set the number, and the written estimate breaks each one out. Rebates come off after, once the pre-approval is in hand.

## Related services

- [Service**Heat pump replacement** A new ducted heat pump in place of one at the end of its life, sized again from the house.](https://clementbostonheatpumps.com/heat-pump-replacement/)
- [Service**Dual fuel heat pumps** A heat pump paired with the furnace you keep, with one control deciding which one heats.](https://clementbostonheatpumps.com/dual-fuel-heat-pump/)
- [Service**Panel and service upgrades** A service load calculation first, and a 200-amp upgrade only when the heat pump and the house need it.](https://clementbostonheatpumps.com/electrical-panel-upgrade-for-heat-pump/)

## Get an estimate for commercial heat pumps

Tell us what heats it now and which rooms aren't working. We'll measure, lay out the system and the ducts, and put the plan and the price in writing.

(857) 837-1475
