# What does a typical heat pump job for a home addition look like, start to finish?

> A West Medford rear addition gets its own ducted heat pump. The load calculation, rough-in, commissioning, price and schedule, start to finish.

URL: https://clementbostonheatpumps.com/blog/heat-pump-for-a-home-addition/

Blog, A Typical Job

A rear family room in West Medford, a furnace that can't reach it, and a small ducted heat pump built into the addition while the walls are still open.

Last Updated: November 12, 2026

The short answer

The addition gets its own small ducted heat pump instead of a branch off the old furnace. Ducts and the line set go in while the framing is open, the equipment goes in after the finishes, and the system is commissioned on its own. Here, the job costs $21,900 and takes four working days on site.

## A typical West Medford addition

[Clement Boston Heat Pumps](https://clementbostonheatpumps.com/) designs a heat pump for a home addition the same way as a whole house: from a load calculation. In this job, a West Medford family adds a one-story rear family room and mudroom to a 1920s colonial.

The addition is 480 square feet over a sealed, insulated crawlspace. The main house keeps its basement gas furnace. The nearest supply trunk ends 30 feet from the new wall, and the furnace already reads 0.78 inch of static pressure, so a branch from it starves the new room.

| Job detail | This addition |
| --- | --- |
| Where | West Medford, National Grid territory |
| House | 1920s colonial with a 480 sq ft rear addition |
| Before | Basement gas furnace; no heat or cooling in the addition |
| After | 1.5-ton cold-climate ducted heat pump for the addition |
| Price | $21,900 before rebates |
| Time on site | Four working days, in two visits |

## What the measurements decide

The room-by-room load calculation for the addition comes to 11,200 BTU an hour of heat on a design night and 9,400 BTU an hour of cooling. That’s a small load, because the builder insulates the new walls and roof to Medford’s energy code.

### Why a small variable-speed unit

A 1.5-ton [variable-speed](https://clementbostonheatpumps.com/guide/variable-speed-heat-pump/) cold-climate unit covers the design load with capacity to spare at 5°F, and it turns down far enough to run steadily on a 45°F day instead of cycling on and off. Our [sizing guide](https://clementbostonheatpumps.com/guide/heat-pump-sizing/) explains why tonnage alone never settles this.

Medford has adopted the state’s specialized energy code, which reaches new construction and major renovations. An all-electric heat pump fits the builder’s energy path for the addition without a second fuel line.

## The rough-in, while the walls are open

The first visit happens after framing and before insulation. Everything that disappears behind drywall goes in now, and the building inspector sees it before it’s covered.

- **Air handler closet.** A vertical air handler goes in a 30-inch closet off the mudroom, with a filter rack and a return grille in the closet door frame.
- **Supply ducts.** Five 6-inch sealed metal runs in the floor framing, inside the insulated crawlspace, to floor registers under the windows.
- **Line set.** An 18-foot run from the closet through the crawlspace rim joist to a side-yard stand.
- **Condensate.** A drain line to the crawlspace pump the builder already plans.

Ducts inside the insulated space lose almost nothing; the same runs in a vented crawlspace leak heat all winter. Our [heat pump ductwork](https://clementbostonheatpumps.com/heat-pump-ductwork/) page covers duct design in more detail.

## Setting the equipment and starting it up

The second visit comes after the floors and paint are done. We set the air handler with 3 kW of backup heat and the outdoor unit on an 18-inch [snow stand](https://clementbostonheatpumps.com/guide/heat-pump-snow-stand/), then wire both.

The existing 200-amp panel has room for two new 240-volt circuits, so no [service upgrade](https://clementbostonheatpumps.com/electrical-panel-upgrade-for-heat-pump/) is needed. Medford’s electrical and sheet metal permits go through the city’s online portal.

### Commissioning, step by step

1. Pressure-test the brazed line set with nitrogen.
2. Pull a vacuum below 500 microns and hold it.
3. Charge by weight for the 18-foot line length.
4. Measure airflow and static pressure at the air handler.
5. Set the thermostat and lock out backup heat above the recorded temperature.

The addition then heats and cools on its own thermostat, separate from the furnace that still serves the rest of the house.

## Price, schedule and rebate

The job costs $21,900 before rebates, inside our typical range of $20,000 to $40,000 and up for a heat pump with new ductwork. It takes four working days on site: two for the rough-in, two to set and start the system.

Because the heat pump serves new space and doesn’t replace an existing fuel, Mass Save’s [basic rebate](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/) applies: $250 per ton, so $375 here. The home’s electric service is National Grid, a Mass Save sponsor.

### Choices that change the number

- **Converting the whole house at the same time.** Replacing the furnace with a [whole-home heat pump](https://clementbostonheatpumps.com/whole-home-heat-pump/) opens the larger whole-home rebate path.
- **Keeping the furnace as backup** for the main house with a [dual fuel heat pump](https://clementbostonheatpumps.com/dual-fuel-heat-pump/).
- **An attic instead of a crawlspace.** A second-story addition often puts the air handler in an [attic](https://clementbostonheatpumps.com/attic-air-handler-heat-pump/), which adds a platform and drain pan.

Wall-mounted ductless units are the other common answer for additions, and our [ducted vs ductless guide](https://clementbostonheatpumps.com/guide/ducted-vs-ductless-heat-pump/) compares the two. If you’re planning an addition, bring us in while it’s still on paper.

## Questions about this post

### Can I just extend my furnace ducts into the addition?

Sometimes, if the furnace has spare capacity, the trunk runs close to the addition and the static pressure has room. In an older house, one of those is usually missing, and the far room ends up cold. We measure static pressure before deciding.

### When should the heat pump installer join an addition project?

Before the framing is closed in. The duct runs, the return path and the line set need to go in after framing and before insulation, so the HVAC rough-in belongs on the builder's schedule from the start.

### Does a heat pump for an addition need its own electrical circuit?

Yes. The outdoor unit and the air handler each need a dedicated circuit, and backup heat adds load. We check the panel at the visit; a 200-amp panel with open spaces usually takes it without an upgrade.

## Keep reading

- [Learn**What size heat pump do I need?** Why square footage and the old unit's tonnage both mislead, what a room-by-room load calculation measures, and how the result turns into equipment.](https://clementbostonheatpumps.com/guide/heat-pump-sizing/)
- [Decision Guide**Should I get a ducted or ductless heat pump?** Both are heat pumps. The difference is how the heat reaches each room, and that comes down to the ducts you have or could add.](https://clementbostonheatpumps.com/guide/ducted-vs-ductless-heat-pump/)
- [Learn**What happens during a heat pump installation?** Each step in a ducted install depends on the one before it. Here's the order, why it runs that way, and how you can tell the job was done right.](https://clementbostonheatpumps.com/guide/heat-pump-installation-process/)
- [Learn**Is a variable-speed heat pump worth it?** How an inverter compressor matches its output to the house, what that does for comfort, cycling and humidity, and when a simpler unit is enough.](https://clementbostonheatpumps.com/guide/variable-speed-heat-pump/)
- [Learn**How do Mass Save heat pump rebates work?** The three rebate tiers, the conditions behind each, the dates that change them, and what happens in towns with their own light plant.](https://clementbostonheatpumps.com/guide/mass-save-heat-pump-rebates/)

## Get an estimate for your house

(857) 837-1475
